manualshive.com logo in svg

Stratus ftServer 2900 Series, Planning And Installation Manual

Share
Download
Stratus ftServer 2900 Series Planning And Installation Manual Download Page 17

Site Planning for ftServer 2900, 4900, and 6900 Systems

1-1

Chapter 1

Site Planning for ftServer 2900, 4900,

and 6900 Systems

1-

For an overview of required information and tasks you need to perform to prepare a site 
for ftServer 2900, 4900, and 6900 systems, see: 

“Site Planning Overview” on page 1-1

 

“Site Planning Checklist” on page 1-3

“System Documentation” on page 1-7

N O T I C E S

1. See 

“Safety Notices” on page 8-1

 for a list of 

important safety notices that you should review as 
part of your site planning. 

2. See 

“Regulatory Notice”

 for information about 

standards compliance. 

Site Planning Overview

Site planning for fault-tolerant systems includes:

Purchasing an appropriate cabinet and monitor

 

Provide a monitor that meets the system’s requirements. 

N O T E

A monitor, keyboard, and mouse are required to install 
Automated Uptime Layer.

If you do not purchase a cabinet from Stratus, provide a cabinet that meets the 
system’s requirements.

Summary of Contents for ftServer 2900 Series





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands