manualshive.com logo in svg

Stratus ftServer 2900 Series, Planning And Installation Manual

Share
Download
Stratus ftServer 2900 Series Planning And Installation Manual Download Page 44

Connections from Storage Systems to ftServer Systems

4-4

Stratus ftServer 29x0, 49x0, and 69x0 Systems: Site Planning and Installation Guide

(R786)

Specifically, see the following figures for supported FC connections between ftServer 
systems to ftScalable Storage Systems:

Single-Host DAS Connections 

Multi-Host DAS Connections 

Dual-Host SAN Connections 

For information about supported FC PCI adapters, see the 

Stratus ftServer Systems: 

PCI Adapter Guide

(R461).

iSCSI Connections 

ftServer systems support iSCSI connections to the storage systems listed in 

Table 4-2

.

N O T E S

1. Ensure that your ftServer system provides adequate 

bandwidth for your iSCSI storage requirements.

2. ftServer systems support only software iSCSI 

initiators in conjunction with standard network 
adapters. Hardware iSCSI HBAs are not supported. 
Contact your account representative for information 
about third-party iSCSI storage systems qualified for 
use with ftServer systems. 

Each ftServer system must contain two available Ethernet adapters (one in each 
CPU-I/O enclosure). You can use embedded Ethernet adapters or U113 Dual-Port 
10/100/1000 Base-T Ethernet PCI-Express Adapters. For better performance you can 
use one of the following:

On VMware vSphere- and Windows-based systems, U117A Dual-Port Fiber 
10-Gbps Ethernet PCI-Express Adapters or U118 Dual-Port RJ-45 10-Gigabit 
Ethernet PCI-Express Adapters, where applicable. 

On Linux-based systems, U584 Dual-Port Fiber 10-Gigabit Ethernet PCI-Express 
Adapter, where applicable.

See the 

Stratus ftServer Systems: PCI Adapter Guide

(R461) for additional information 

about supported Ethernet adapters. 

Summary of Contents for ftServer 2900 Series





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands