background image

STRATCO EZI-SLAT FENCING INSTALLATION GUIDE

INSTALLING POSTS

POST LOCATIONS

Determine the location for the Ezi-Slat Fence using a temporary 
string line (Figure 1.0). Measure and mark the required distance 
between posts. Standard panel length is 941/2” (2400mm) 
between the inside edges of the posts. The spacing for a 
standard swing gate is 401/5” (1020mm). For custom panels and 
gates you will need to determine the required post spacing.

POST INTO CONCRETE

Dig holes at the correct distances (see Figures 1.0 & 1.1). 
Holes are to be 10” (250mm) in diameter and 2’ (600mm) 
deep (Figure 1.2) or in accordance with minimum footing size 
for the engineered fence solution.

If using aluminum posts, they must not come into direct 
contact with concrete, as this will prematurely corrode the 
posts. There are two recommended methods for installing 
in-ground aluminum posts.

ALUMINUM POST DIRECTLY INTO CONCRETE

Cover the end of the post with duct tape and apply 
a coating of bitumen paint to the section of the post 
which will come into contact with the concrete to avoid 
corrosion. The post must be embedded  into the concrete 
a minimum of 18” (450mm) (Figure 1.2).

Using a spirit level ensure the posts are plumb, and check 
that the distances between posts are correct.

STEEL SPIGOT INTO CONCRETE

A 11/2”x11/2”x1/6” (40x40x4.0mm) SHS steel spigot can be 
installed into concrete (Figure 1.2). The spigot must protrude 
from the concrete a minimum of 2’. The Ezi-Slat Aluminum 
Post can then be slid down onto the spigot (Figure 1.3).

INSTALLING POST ONTO CONCRETE*

Screw the base plate onto the Ezi-Slat Aluminum Post using 
four 12g x 3” (75mm) pan head screws (Figure 1.4).

Ensure the distance between posts is correct. It is 
recommended that there is a minimum distance of 3” 
(75mm) from bolt centres to the edge of the concrete. Using 
a hammer drill and a 25/64” (10mm) masonry drill bit, drill 
four holes into the concrete. Fasten the base plate to the 
concrete using four M10 masonry anchors (Figure 1.5).

*Note: This application is only recommended for low height 
garden fencing or similar in which an engineered solution is 
not required.

Standard Fence Panel Post Spacing

94½” (2400mm)

Standard Gate Post Spacing

40

1

5

” (1020mm)

FIGURE 1.1

String Line

Spirit level

Standard Fence Panel;

94½” (2400mm)between posts

Standard Gate;

40

1

5

” (1020mm)

between posts

FIGURE 1.0

2’

(600mm)

min.

6” (150mm) layer of
concrete mix,

agitated before
each subsequent

layer is poured.

10” (250mm)

Final layer
shaped to

slope away

from posts.

6”(150mm)

18”

(450mm)

min.

Bitumen Paint

required for

Aluminum Posts

FIGURE 1.2

Aluminum Post

1½”x1½”x¹⁄

6

(40x40x4.0mm)
SHS Spigot

2’ (600mm) Min.

Concrete Footing

FIGURE 1.3

Summary of Contents for Fence Sanctuary Ezi-Slat Fencing











Reviews: