Strand VISION.NET User Manual Download Page 4

User ManUal

w w w. s t r a n d l i g H t i n g .co M

Vision.net Hardware   

4

COMPLIANCE NOTICE

FCC DECLARATION OF CONFORMITY 

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 

15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when 

this equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio 

frequency energy and, if not installed and used in accordance with Vari-Lite Strand system, service, and safety 

guidelines, may cause harmful interference to radio communications.
As tested under this standard:

FCC 47CFR 15B clA*CEI

Issued:2009/10/01 Title 47 CFR Part 15 Subpart B Unintentional Radiators Class A
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user 

will be required to correct the interference at his/her own expense.

EU DECLARATION OF CONFORMITY

We, Vari-Lite LLC., 10911 Petal Street, Dallas, Texas 75238, declare under our responsibility for the products 

contained herein are in conformity with the essential requirements of the following European Directives and 

harmonized standards:

Low Voltage Director (LVD), 2006/95/EC

EN 60589-2-17:1984+A1:1987+A2:1990 used in conjunction with 60598-1:2008/A11:2009

Electromagnetic Compatibility Directive (EMC), 2004//108/EC

EN 55022:2010, EN55024:2010

Summary of Contents for VISION.NET




















Reviews: