13
12
5. FACTORS INFLUENCING VAPORIZATION
The amount of aromas and fragrances
released can be influenced by the fol-
lowing factors:
1. Quality: The amount of aroma or
fragrance contained in the respec-
tive plant material that can be va-
porized.
2. Quantity: The amount of vaporiza-
tion material in the Filling Cham-
ber.
3. Surface: The finer the plant is
ground, the greater the surface
and the more aromas and fra-
grances can be released during
the vaporization cycle.
4. Temperature: The higher the tem-
peratures, the more aromas and
fragrances will be released at
once.
Please note: Increasing the tempera-
ture should be the last resort, because
plant material tastes more roasted
when using higher temperature.
Since the plant ingredients are re-
leased in a gentle manner, the vapori-
zation cycle may be repeated with the
same contents in the Filling Chamber.
Depending on the four factors de-
scribed above, the Filling Chamber
contents may be reused multiple
times until the aromas and fragrances
are released completely.
If no more vapor is produced at the
highest temperature, then the vapori-
zation material is completely exhaust-
ed and must be replaced with new
material. However, for the best aroma
results it is advisable to replace the
vaporization material before this
point.
6. THE
MIGHTY
VAPORIZER
Unpacking
The box contains all components as
well as the Instructions for Use. Keep
the Instructions for Use for future ref-
erence.
Remove the Vaporizer and the acces-
sories from the box. Immediately after
unpacking, check whether the Vapor-
izer, the accessories, the power
adapter and the device plug are all
included in the delivery and work
properly. If you notice any defects, in-
form the seller or the delivery agent
immediately.
The packing material (plastic
bags, boxes etc.) must be
kept out of the reach of chil-
dren as it is a potential source of dan-
ger.
Please dispose of the packing mate-
rial in a proper and environmentally
friendly manner.
We recommend keeping the original
packaging in case it is required later
(transport, Storz & Bickel Service
Center etc.).
6. THE
MIGHTY
VAPORIZER
Power Connection
Before connecting up the Vaporizer,
make sure that the information given
on the power adapter type label cor-
responds to the local power supply
voltage.
All parts of the electrical system must
comply with currently applicable offi-
cial regulations.
Place the heated Vaporizer only on a
hard, stable surface, and not on any
soft or heat-sensitive material.
Take care that the power adapter cord
cannot be damaged through kinking,
crushing or pulling.
Improper installation may
lead to personal injury or ma-
terial damages, for which the
manufacturer cannot be held respon-
sible.
Application and Operation
This Vaporizer was devel-
oped for vaporizing the plant
materials listed in the plant
overview. Any other use is inappropri-
ate and potentially dangerous.
The user should always follow the
instructions listed here for use and
maintenance.
If you have any concerns, or if there
are any problems immediately switch
off the Vaporizer and pull the power
adapter cord, if used, from the socket.
Do not try to remedy the defect your-
self. Contact our Service Center di-
rectly.
After using the Vaporizer and power
adapter, allow them to cool down be-
fore placing them in storage.
Storage
Store the Vaporizer and the power
adapter in a dry place protected
against the effects of weather and out
of the reach of children or unqualified
persons.
In Case of Problems
If the power adapter has been in use,
unplug it at the socket and ensure that
no one can connect the Vaporizer to
the mains supply again without this
being noticed.
Before any maintenance work is done,
the Vaporizer has to be switched off
and the power adapter unplugged
from the power supply.
Put the Vaporizer in the original pack-
aging, or pack it properly in other
packing material, and send it to our
Service Center.
