WARNING:
Never touch hot soleplate at any time before cooling down!
Steam ironing
1.
Put the unit base on a stable and level surface.
2.
Remove the water tank and fill it with water through the filling aperture. You had better
use purified water with less calcium particles. The max capacity of water tank is 1.6L, the
water level shall not be exceeded the MAX mark.
3.
Put the iron on the thermal insulation stand of unit base.
4.
Connect the plug to wall outlet, one beep can be heard, then turn the temperature dial to
the second setting or the temperature higher than the second setting. Refer to
“
IRONING
TIPS
”
and
“
ADDITIONAL TABLE
”
as below when select temperature.
5.
Press the ON/OFF button, the power indicator illuminates, the temperature indicator and
ECO steam rate indicator illuminate. The default setting is the ECO steam rate when the
appliance is turned on.
6.
And you can select the desired steam rate for each garment according to your
requirement. There are two modes including MAX and ECO steam rates available. Make sure
that there is enough water in the tank.
7.
The iron starts heating, after a few minutes, the temperature indicator extinguishes, it
indicates the soleplate temperature has achieved the selected temperature.
8.
When the indicator of selected steam rate lights solidly, it indicates that the iron is ready
for ironing garment with steam. Refer to
“
IRONING TIPS
”
and
“
ADDITIONAL
TABLE
”
as below when ironing.
9. Press the steam trigger with a little force, the steam will be sprayed from the soleplate
continuously, and then you can iron the garment with steam.
NOTE:
There may be dripping water during spraying steam when the temperature is lower
than that of the second setting. This is normal.
CAUTIONS:
1) Do not touch hot soleplate at any time before cooling down!
2) Never direct the steam at people!
3) Do not activate the steam function when the iron is placed on the unit base to avoid being
scalded by steam.
8. After ironing, remove the plug from the wall socket, the appliance will be turned off and
all the indicators will extinguish, then unplug the appliance. But the soleplate is still hot,
never touch it with hand, place it on the thermal insulation stand until it cools down
completely.
CLEANING AND MAINTENANCE
Before cleaning, firstly disconnect the power outlet and let the appliance cools down.
1. Wipe the residues and any other deposits on the soleplate with a damp cloth or a non-
abrasive (liquid) cleaner.
NOTE:
Do not use chemical, steel, wooden or abrasive cleaners to scrape the soleplate.
2. Clean the upper part of iron with a soft damp cloth. Wipe the water drop on the unit base
and the thermal insulation stand with dry cloth.
3. Remove the water tank, upend the unit base and put it on a flat surface, then
anticlockwise rotate the knob at the bottom of unit base to remove it (see Fig.1) .
Summary of Contents for SP1070
