Still ECH 12 Original Instructions Manual Download Page 75

Page: 75 / 110

CAUTION

Before lifting a load, ensure that its weight does not

exceed the truck’s maximum load capacity.

–

Refer to the rated load capacity specified on the

truck's identification plate.

–

Ensure that the load is stable and uniform to pre-

vent any partial spillage.

–

Check that the width of the load is compatible with

the width of the forks.

DANGER

It is mandatory to wear safety footwear for pedes-

trian mode driving.

WARNING

Transporting people is strictly prohibited.

CAUTION

Take care not to disturb any adjacent loads, or those

which may be to the side or in front of the load being

handled.
Loads should be laid out as follows:

–

Line up loads with a small space between each

one and its neighbour to avoid any fouling.

CAUTION

Only transport loads that have been positioned and

secured in accordance with regulations.
Take appropriate protective measures if the load is at

risk of tipping over or falling during transport.

–

Approach the load carefully.

–

Adjust the height of the forks until they can

be easily inserted into the pallet.

–

Insert the forks under the load.

–

If the load is shorter than the forks, position

the forks so that the front of the load over-

hangs them by a few centimetres, to avoid

interference with the load immediately

ahead.



Operation

Load handling

5001 801 1505 EN - 12/2019

Summary of Contents for ECH 12















































































































Search results

Summary of Contents for ECH 12

Reviews:

Related manuals for ECH 12

Brands by name

Popular brands

Still ECH 12, Original Instructions Manual

Search results

Summary of Contents for ECH 12

Reviews:

Related manuals for ECH 12

Brands by name

Popular brands