Still ECH 12 Original Instructions Manual Download Page 71

Page: 71 / 110

Emergency stop

–

Press the emergency switch (2). All power

will be cut off and the vehicle will stop work-

ing.

CAUTION

When the emergency stop button (2) is pressed, it

will lock in position.Rotate the button clockwise half a

turn to release it.Do not pull hard, as it will reset on

its own.

CAUTION

The condition of the floor surface affects the braking

distance of the truck and should be taken into con-

sidered by the operator.

Using the truck on a slope

NOTE

Incorrect use of the truck on slopes is not rec-

ommended.It places particular stress on the

traction motor, brakes and battery.

Be particularly careful near slopes:

●

Never attempt a slope with a gradient great-

er than that specified in the truck's data-

sheet.

●

Make sure that the ground is dry with a non-

slip surface and that the route is clear.



Operation

Drive system

5001 801 1505 EN - 12/2019

Summary of Contents for ECH 12















































































































Search results

Summary of Contents for ECH 12

Reviews:

Related manuals for ECH 12

Brands by name

Popular brands

Still ECH 12, Original Instructions Manual

Search results

Summary of Contents for ECH 12

Reviews:

Related manuals for ECH 12

Brands by name

Popular brands