INSTALLATION
Mise hors service
www.stiebel-eltron.com
LWE 40 |
55
FR
AN
ÇAI
S
7. Mise hors service
7.1 Mise hors service temporaire
f
f
Utilisez le disjoncteur de l’installation domestique pour cou-
per l’alimentation électrique de l’appareil.
f
f
Fermez l’obturateur intérieur pour éviter les déperditions
calorifiques.
7.2 Mise hors service pour une période prolongée
f
f
Retirez l’obturateur intérieur.
f
f
Sortez l’unité de ventilation du boîtier mural encastrable.
f
f
Remplissez le boîtier mural encastrable d’isolant. Ceci facili-
tera le montage ultérieur d’un nouvel appareil.
f
f
Fermez l’obturateur intérieur.
8. Aide au dépannage
Le témoin
de défaut
clignote x
fois
Cause
remède
1
Panne du venti-
lateur
Identifiez le ventilateur sur lequel le dé-
faut survient. Si un ventilateur est bloqué,
éliminez-en la cause.
Au moins un ventilateur envoie un signal
d’alarme erroné par le biais du conduc-
teur jaune. Vérifiez la tension (conducteur
jaune – GND).
Fonctionnement normal : > 14,4 V
Alarme : < 1,65 V
État indéfini : 1,65 V < x < 14,4 V
Le cas échéant, remplacez le ventilateur.
2
Erreur de niveau
lors de la recon-
naissance du sys-
tème
Vérifiez l’alimentation électrique du ven-
tilateur.
Vérifiez si le conducteur jaune du ventila-
teur est correctement raccordé.
Vérifiez la sortie d’alarme du ventilateur.
3
Défaut de commu-
nication
Vérifiez les conducteurs entre l’unité de
commande et la carte adaptatrice.
Vérifiez que la carte adaptatrice est
correctement enfichée sur le module de
commande. Voir le chapitre «Montage
/ Raccordement électrique / Raccorder
l’unité de commande au module de com-
mande».
Vérifiez si un contact sur la carte adapta-
trice est cassé ou tordu.
4
Défaut lors de la
reconnaissance du
système (défaut de
stabilité)
Vérifiez l’alimentation électrique du ven-
tilateur.
Vérifiez si le conducteur jaune du ventila-
teur est correctement raccordé.
Vérifiez la sortie d’alarme du ventilateur.
5
L’unité de com-
mande et l’en-
semble de com-
mande ne sont pas
compatibles.
Interrogez l’unité de commande pour
connaître les composants formant l’ins-
tallation. Vérifiez la compatibilité entre
les différents composants installés dans
le système.
Remplacez l’unité de commande par une
unité de commande adaptée.
clignote en
permanence
La programmation
du module de
commande est in-
correcte.
Recommencez la programmation du mo-
dule de commande. Si la programmation
échoue, rétablissez les réglages d’usine
par une réinitialisation.
9. Données techniques
LWE 40
236659
Données acoustiques
Niveau de puissance acoustique L
wtot
rap-
porté au débit volumique d’air
dB(A)
32 (pour 20 m³/h),
37 (pour 30 m³/h)
Écart de niveau sonore normé
dB
37
Limites d’utilisation
Plage de température de fonctionnement
°C
de -15 à +40
Données énergétiques
Classe d’efficacité énergétique par condi-
tions climatiques moyennes, gestion selon
la demande locale
A
Données électriques
Puissance absorbée
W
2-7
Tension nominale
V
24
Versions
Classe de filtre
ISO Coarse > 60 % (G4) |
ISO Coarse > 30 % (G2)
Indice de protection (IP)
IP41
Dimensions
Hauteur
mm
258
Largeur
mm
258
Profondeur
mm
550
Hauteur d’installation maximale
m
2000
Ouverture de passage mini.
mm
Ø200, carré 185x185
Poids
Poids
kg
4,25
Valeurs
Débit volumétrique de l’air
m³/h
20/30/40/49/70
Débit volumique de l’air mode différentiel
m³/h
10/15/20/25/35
Rendement de récupération de chaleur,
jusqu’à
%
93
Épaisseur de mur
mm
300 - 550
Boîtier mural encastrable
LWE 40 TG-550
LWE 40 TG-800
236662
236663
Épaisseur de mur
mm
300 - 550
550 - 800
Longueur
mm
550
800
Hauteur
mm
200
200
Largeur
mm
202
202
Autres données
Version logicielle
≥ 3.0.0