Stid Architect LEGIC ARC Le2 Series Installation Instructions Manual Download Page 2

Page: 2 / 13

13.56 MHz Legic®
Upgradable readers ARC
Installation instructions

13,56 MHz Legic®
Lecteurs évolutifs ARC
Notice d’installation

13.56 MHz Legic®
Lectores escalables ARC

Procedimiento de instalación

conforme con

NOM-024 -SCFI-2013

sur

Ed. 06/06/2019

Product references

Power supply characteristics

Use an AC/DC power supply type LPS, Limited Power Source (as per IEC EN 60950-1 Ed2) or type ES1, PS1 (according to IEC EN 62368-1) for the main supply.
Main power supply: Range: +7 Vdc to +28 Vdc

Typical: 12 Vdc

Max. consumption at 12 Vdc:
ARC-L: 130 mA / ARC-M: 160 mA / ARC-N: 200 mA / ARC-O: 280 mA / ARC-P: 310 mA / ARC-Q: 350 mA

Characteristics

Communication:

RS485 (L+ & L-) / RS232 (TD & RD) / TTL (Wiegand / Clock and Data)

Connection:

Removable connectors 1x10 pins and 1x2 pins, thread 0.19685 inch

Protection:

IP65, excluding connectors

Static relay:

ASSR-1218-003E: 60 V output withstand voltage / 0.2A current rating / low on-resistance 1

Ω typical for AC/DC

Recommended cables

Use a multi-conductor shielded twisted pair cable.
Max. length RS485: 328.1 ft at 9600 baud

Max. length RS232: 49.2 ft

Wiegand / Clock & Data:

1 pair AWG24

– 98.4 ft max / 2 pairs AWG24 – 196.9 ft max / 3 pairs AWG24 – 328.1 ft max

1 pair AWG20

– 164.0 ft max / 2 pairs AWG20 – 328.1 ft max

Buzzer / LED

The operating mode for the Buzzer and LED 1 and 2 can be programmed by configuration (R3x) or controlled by the remote system with a 0 Vdc respectively on
the

“

Led 1

”, “

Led 2

” and “

Buzzer

” inputs of the reader’s connector or controlled by the communication protocol of the reader (W3x).

Anti-tearing

Tearing is detected by an accelerometer

. When the reader is wrenched, the switch output (connector J2) provides an O/C contact to indicate the tearing of

reader.

▪

for R31 reader: the wrenching signal will be

emitted on the “Data/Data1” line. This function is configurable via configuration.

▪

for W32 and 33: the reader will perform the operations configured with the SSCP protocol.

Caution: switch on the reader when it is in its final position to initialize the accelerometer in the correct position.

Relay

Read-only reader, except touch screen: automatic tamper management.
Touch screen read-only reader: if the bell is activated, contact J2 is used to connect the external ring (max. 200 mA at 28 Vdc).
Read/Write reader: the relay is controlled by the SSCP protocol commands.

Read-only reader configuration

R readers are configurable by serial link for non-secure paramete

rs and by master card SAM to access secure data on user’s card.

Reader retrieve configuration from SAM at any time.

- If the SAM is accepted, LED lights green, maintain the SAM in front of the reader until the buzzer beeps 5 times.
- If the SAM is not accepted, LED lights red and buzzer is activated 1s.

Powering-up the readers

On power-up, the reader enters an initialization phase:

1. Activation of the white LED and buzzer for 100 ms.

For read-only readers:

2. Activation of the LED, according to the color code: Red = +10, Orange = +5, Green = +1, indicating the firmware version.

3.  For serial ARC only: the orange LED flashes 20 times: waiting for an update.
4.  Activation of the default LED (flashes blue if no customer specific configuration).
5.  ARC Screen: display of the default image.

Precautions for the biometric sensor and keypad

▪

For optimal operation, the biometric sensor must be free of all traces of water. Outdoors it is recommended to install the reader under cover.

▪

The keypad is sensitive. Take off your gloves to enter your code.

▪

For the ARC screen with an activated keypad, the default mode is: display the keyboard

ARC-X-Le2

L: Standard
M: Keypad
N: Touch screen

O: St Biometrics
P: Biometrics
Q: Touch Biometrics

J6: Antenna connector

J7: Keypad connector

J9: Biometric connector

J14: Display connector

J2: O/C contact

Connector