background image

 

 

 

Stewart Filmscreen –

 

Balón 

 

22 

 

 

support at Stewart Filmscreen. 
 

ONE (1) YEAR LIMITED WARRANTY 

 

STEWART FILMSCREEN CORPORATION (Stewart) warrants all products to the original purchaser 
only. Stewart products are guaranteed to be free from defects in materials and workmanship for a 
period of one (1) year from the date of purchase by the original purchaser or eighteen (18) months 
from  date  of  manufacture,  as  defined  in  the  serial  number.  Additionally,  all  products  must  be 
properly operated and maintained according to Stewart instructions and cannot be damaged due 
to improper handling or treatment after shipment from the factory. This warranty does not apply to 
equipment showing evidence of misuse, abuse, or accidental damage, including neglect caused by 
improper installation (i.e. proximity to hot lights, exposure to extreme heat or cold, exposure to 
excessive humidity, etc.).  
 
Stewart on-site warranty repair services are not available for this product. Stewart’s sole obligation 
under this warranty shall be to repair or to replace (at Stewart’s sole discretion) the defective part 
of  the  merchandise.  This  warranty  expressly  does  not  cover  any  costs  of  removal,  installation, 
framing,  or  other  costs  incidental  to  replacing  the  screen  or  returning  it  to  Stewart.  Returns  for 
service should be made to your Stewart dealer. If it is necessary for the dealer to return the screen 
or  part  to  Stewart,  transportation  (freight)  expenses  to  and  from  Stewart  are  payable  by  the 
purchaser. Stewart is not responsible for damage in shipment. To protect against damage or loss in 
transit, insure the product and prepay all transportation expenses.  
 
This warranty is in lieu of all other warranties, expressed or implied, including warranties as to fitness 
for use or merchantability. Any implied warranties of fitness for use, or merchantability, that may be 
mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives 
you specific legal rights, and you may also have other rights which vary from state to state. In no 
event will Stewart be liable for sums in excess of the purchase price of the product. No liability is 
assumed by Stewart for expenses or damages resulting from interruption in operation of equipment, 
or for incidental, direct, or consequential damages of any nature. In the event that there is a defect 
in  materials  or  workmanship  of  a  Stewart  Filmscreen  product,  you  may  contact  our  Customer 
Service Department at 1161 W Sepulveda Blvd, Torrance, California 90502- 2797, or call us at 1 (310) 
784-5300, or toll free at 1 (800) 762-4999.  
 
IMPORTANT: This warranty shall not be valid and Stewart shall not be bound by this warranty if the 
product is not operated and maintained in accordance with Stewart’s written instructions. Stewart 
Filmscreen Corporation shall not be liable for any and all consequential damage(s) occasioned by 
the breach of any written or implied warranty pertaining to the sale of a Stewart Filmscreen product 
in excess of the purchase price of the product sold. 
 

Summary of Contents for Balon Series
























Reviews: