18
19
Warning
Descripti on
1 Beep
2 Beeps
3 Beeps
4 Beeps
Minimum Sensiti vity
Small Sensiti vity
Average Sensiti vity
Maximum Sensiti vity
If you need to leave your vehicle at the mechanic, carwash, a place with valet service
or other such places, you can acti vate the valet functi on without showing them where
the
MASTER BUTTON
is or giving them the presence control.
Press the
MASTER BUTTON
3 ti mes, it will emit 2 beeps, the locks menti oned in items
6.1
,
6.2
and
6.3
are temporarily disabled. Each ti me the igniti on is turned on or off ,
it will emit 2 beeps to warn the user that the vehicle is unprotected. To acti vate the
anti -theft functi ons again press the
MASTER BUTTON
once. When using the presence
functi on you need to press on the
CX-1P
presence control near the car.
This output allows you to acti vate and deacti vate the radio/sound/video of the vehicle
using the alarm. The sound control output is
ON
, in the following situati ons:
• When energizing the alarm / When the igniti on is on with the alarm off / When
opening the door with alarm off and igniti on off / Disabling the alarm aft er a violati on
/ When unlocking using the presence control.
The sound control output is turned
OFF
in the following situati ons:
• When acti vati ng the alarm / When the lockdown warning begins/ When signaling
that you are in valet mode.
NOTE: If the sound equipment requires a control current
greater than 150 mA, use an external relay.
The alarm has an auxiliary power circuit that takes over if the vehicle’s ba� ery is
disconnected. The auxiliary power supply must be fed by a 9V ba� ery connected to
the 2-way connector on the side of the control panel. If the main power is cut when
the alarm is on, the auxiliary circuit triggers the siren and locks the vehicle.
Cables and
auxiliary batt ery must be purchased separately.
When the alarm is deacti vated aft er going off and the igniti on is turned on, the LED
fl ashes a number of ti mes to indicate what triggered the alarm the last ti me the alarm
was acti vated. If the alarm went off more than once, the LED reports the fi rst trigger.
If you want to see the trigger again, simply turn the igniti on off and on. Another way
to generate this signal is to press the bu� on when the alarm is off . The trigger
given for the alarm going off remains valid unti l the alarm is acti vated again.
The table
below shows the number of fl ashes the LED gives and the corresponding trigger:
Turn the igniti on on (or the car is on) hold down the bu� on and press on the CX-
1P control unti l the led goes out and blinks twice, wait for the lock ti me.
The ultrasound has 4 levels of sensiti vity:
VALET PARKING FUNCTION
SOUND CONTROL
BACKUP BATTERY
LED TRIGGER REPORT
LOCK TEST BY PRESENCE
ULTRASOUND ADJUSTMENT
8
14
16
17
7
15
This
MASTER BUTTON
needs to be installed in a concealed but easily accessible place.
From this bu� on you can confi gure alarm functi ons
(see secti on 18)
.
The control panel can be switched on and off by programming
(see table secti on 18,
functi on 9).
MASTER BUTTON
ENABLE OR DISABLE ALARM
10
9
If you lose your remote control, you can deacti vate the control panel by turning the
igniti on on and touching the
MASTER BUTTON
.
DISABLE ALARM WITHOUT CONTROL
11
NOTE:
When the alarm is off and the vehicle has a door open, you will noti ce a visible light as the
ultrasonic sensor detects movement. This facilitates adjusti ng the sensor for each vehicle.
To cancel the lock down, press the on the presence control.
In order to deacti vate the control unit without the remote control, turn on the
igniti on and press the
MASTER BUTTON
. If the presence functi on is acti vated, the
locks menti oned in secti ons
6.1 (Anti -theft through the DOOR)
and
6.2 (Anti -theft
functi on in the IGNITION)
will not be functi oning.
3 quick taps on the
MASTER BUTTON
1 quick tap on the
MASTER BUTTON
Disables the locks menti oned in
secti ons
6.1
,
6.2
and
6.3
Enables the locks menti oned in
secti ons
6.1
,
6.2
and
6.3
(If enabled)
Press
Siren emits 2
beeps
No beeps
Functi on
Alarm Response
If the alarm is enabled and disabled and nothing happens aft er it is disabled, the alarm
will be acti vated again. If there is any change in the igniti on, doors or hood during this
ti me, the alarm will not be acti vated. This functi on can be programmed
(see secti on 18)
.
AUTOMATIC ALARM ACTIVATION
13
PROGRESSIVE LOCK CYCLE
12
LOCK FOR
2 SECS.
UNLOCK
FOR 10 SECS.
LOCK FOR
2 SECS.
UNLOCK
FOR 2 SECS.
LOCK FOR
2 SECS.
UNLOCK
FOR 5 SECS.
COMPLETELY
LOCKED
