background image

The manufacturer has set the water treatment unit's sequence of cycles, cycle times, salt dose,
exchange capacity and gallon capacity. For water softeners, the salt dose refill time has been preset.
For iron filters, the regeneration tank refill time has been preset.

The dealer

 should read this page and guide the installer regarding hardness, day override, and

time of regeneration, before installation:

For the installer, 

the following must be used:

● Set Installer Settings … Hardness, Day Override (preset to 12 days), and Time of
    Regeneration (preset to 2 am)
● Read Normal Operating Displays
● Set Time of Day
● Read Power Loss & Error Display

Water Softeners:

During operation, the normal user displays are time of day or gallons remaining before regeneration
will occur. Days remaining is an optional display but is not normally used. Each of these can be 
viewed by pressing 

NEXT 

to scroll through them. When stepping through any displays or programming, 

if no buttons are pressed within 5 minutes, the display returns to a normal user display. Any changes
made prior to the 5 minute time out are incorporated.
To quickly exit any Programming, Installer Settings, etc., press 

SET CLOCK.

 

Any changes made prior to

the exit are incorporated.
If desired, two regenerations within 24 hours are possible with a return to the preset program. To do

double regeneration:

1. Press the 

REGEN 

button once. 

REGEN TODAY 

will flash on the display.

2. Press and hold the 

REGEN 

button for three seconds until a regeneration begins.

Once the valve has completed the immediate regeneration, the valve will regenerate one more time
at the preset time.

The bypass valve is typically used to isolate the control valve form the plumbing system's water
pressure in order to perform control valve repairs or maintenance. The 1" full flow bypass valve
incorporates four positions including a diagnostic position that allows a service technician to have
pressure to test a system while providing untreated bypass water to the building.
Be sure to install bypass valve onto main control valve, before beginning plumbing
or make provisions in the plumbing system for a bypass.
The bypass body and rotors are glass filled Noryl

® 

and the nuts and caps are glass filled 

polypropylene. All seals are self-lubricating EPDM to help prevent valve seizing after long periods of
non-use. Internal "O" Rings can easily be replaced if service is required.
The bypass consists of two interchangeable plug valves that are operated independently by red 
arrow shaped handles. The handles identify the direction of flow. The plug valves enable the bypass
valve to operate in four positions.

PREINSTALLATION INSTRUCTIONS FOR DEALERS:

BYPASS VALVE:

3

Summary of Contents for HE Series






















Reviews: