background image

13

12.3 Production percentage setting (with the automatic cover open)

The amount of chlorine produced depends on salt content (4 g/l), water quality,  

appliance operating time and production percentage.
The production percentage is set depending on the chlorine required in the pool 

(between 0.8 and 1.5ppm).
•  Press the P key and keep it pressed.
•  Set the power using the + or– keys.
The value displayed on the screen increments in 5 % steps. Setting from 30 % to 180 % 

possible.
Every week, measure the pH and the chlorine.

12.4 Forced operation activation

Forced operation uses the maximum authorised electrode power to carry out stronger 

chlorination.
Maximum forced operation time: 24 hours.
After 24 effective hours, production switches back to normal mode.
Only runs with the automatic cover open.
•  Press the F key and keep it pressed for 5 seconds. 
The value displayed on the screen increments in steps of 5 % to reach 200 %.
Possibility of returning to Automatic mode before the 24 effective hours by pressing  

the A key for 5 seconds.

12.5 Connecting the supplied slatted cover cable (Slow Mode)

•  Connector to be connected to the left side of the box marked Coupling. 
•  2 wires to strip and connect to the automatic cover contact (Slow mode).

Caution:  

no voltage on the automatic cover cable (VOLTAGE 0 Volt, dry contact).

12.6 Production percentage setting (with the automatic cover closed)

This setting makes it possible to have a different adapted production when the automatic cover is closed.
By default, if your connection between the electrolyser and the automatic cover box has been set up, when the cover 

closes, production is divided by 2.
The production percentage depends on the chlorine required in the pool (between 0.8 and 1.5 ppm).
•  Fully shut your pool cover.
•  Press the P key and keep it pressed.
•  Set the power using the + or - keys.
The value displayed on the screen increments in 5 % steps. Setting from 30 % to 180 % possible.

Important:  

your closed slatted cover setting can be higher than the open slatted cover setting.

Every week, measure the pH and the chlorine.
When your slatted cover is closed, it is not possible to activate forced operation.

Summary of Contents for EVOLUTION SYSTEME 7 SEL EVO



















Reviews: