background image

2

 Safety Instructions:

WARNING

 - to guard against injury, basic safety precautions should be 

observed, including the following:

1.  

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

2.  

CAUTION

 - Always disconnect power before servicing.

3.  

DANGER

 - To avoid possible electric shock, special care should be taken 

since water is present near electrical equipment. Unless a situation is 

encountered that is explicitly addressed by the provided maintenance 

and troubleshooting sections, do not attempt repairs yourself, refer to an 

authorized service facility.

4.   Carefully examine the disinfection system after installation. It should not 

be plugged in if there is water on parts not intended to be wet such as, 

the ballast or lamp connector.

5.   Do not operate the disinfection system if it has a damaged cord or 

plug, if it is malfunctioning or if it has been dropped or damaged in any 

manner.

6.   Always unplug the disinfection system before performing any cleaning 

or maintenance activities. Never yank the cord to remove from an outlet; 

grasp the wall plug and pull to disconnect.

7.   Do not use this disinfection system for other than intended use (potable 

water applications). The use of attachments not recommended or sold by 

the manufacturer/distributor may cause an unsafe condition.

8.   Intended for indoor use only. Do not install this disinfection system 

where it will be exposed to the weather or to temperatures below 

freezing. Do not store this disinfection system where it will be exposed 

to the weather. Do not store this disinfection system where it will be 

exposed to temperatures below freezing unless all water has been 

drained from it and the water supply has been disconnected.

9.   Read and observe all the important notices and warnings on the water 

disinfection system.

10.   If an extension cord is necessary, a cord with a proper rating should 

be used. A cord rated for less Amperes or Watts than the disinfection 

system rating may overheat. Care should be taken to arrange the cord so 

that it will not be tripped over or pulled. Circuit breaker must not exceed 

power cord current rating (ie - 15A for North american NEMA 5-15P). 

11.   SAVE THESE INSTRUCTIONS.

Warning:

 The UV light given off by this unit can cause serious burns to 

unprotected eyes and skin. Never look directly at an illuminated UV lamp. 

When performing any work on the UV disinfection system always unplug the 

unit first. Never operate the UV system while the UV lamp is outside of the 

UV chamber.

 

Note:

 The UV lamp inside of the disinfection system is rated at an effective life of 

 approximately 9000 hours. To ensure continuous protection, replace the UV lamp   

 annually.

WARNING

 - Always shut-off water flow and release water pressure before 

servicing.

Summary of Contents for Aquasana SC200-A



















Reviews: