Wireless - LED underwater spotlights for liner pools 2015_V2
Page 4 of 30
EN
Safety instructions
Read through these instructions carefully
before you use the product.
¾
The instructions you are holding contain
important information relating to safety
measures required for installation and ini-
tial operation. Therefore the installer and
the user must read these through carefully
before starting the installation.
¾
Keep these instructions carefully for fu-
ture use.
¾
Those responsible for assembly should
also be appropriately qualified for this type
for work.
¾
Avoid contact with electric current.
¾
Observe the appropriate norms and
standards regarding accident prevention.
¾
In this regard, standard IEC 364-7-702 for
electrical connection in buildings, particu-
larly cabling in swimming pools, must be
observed.
¾
The power supply must be removed be-
fore any activity relating to maintenance or
exchange of parts is carried out.
¾
The manufacturer is not responsible un-
der any circumstances for assembly, in-
stallation or commissioning of any electri-
cal components, which were handled and
incorporated in any location except their
own premises.
¾
This equipment is not intended for use by
anyone (including children) with restricted
physical, sensory or mental ability, or with
limited experience and / or limited
knowledge, unless they are supervised by
someone responsible for their safety, or
they receive instruction from them regard-
ing the use of the equipment.
1
General information
This underwater lighting has been designed for pools for full use un-
der water. It is a class III electrical device with very low voltage for
safety reasons (12V AC). The bulb complies with IPX8 protection
(resistance to penetration by dust, moisture and foreign bodies) at
an immersion depth of 2 m. In addition this incorporates the interna-
tional safety standards for lighting, in particular standard EN 60598-
2-18.
The manufacturer is not responsible under any circumstances for
assembly, installation or commissioning of any electrical compo-
nents, which were handled and incorporated in any location except
their own premises.
2
Technical data:
LED light
13 W with RGB colour changer
Rated supply
12 V
Electricity supply
Alternating current
Power
PAR 56, 12 V, Alternating cur-
rent
Protection
IPX 8
Should only be used with a swimming pool safety transformer!
Only turn the lighting on underwater!
3
Installation instructions
To avoid
any
blinding effects, the
spotlights
should be installed fac-
ing away from the property and the usual line of sight to the swim-
ming pool.
So you don’t have to
empty the pool when changing the lamps
, we
recommend installing the lamps in areas which are
easily accessible
from the upper edge of the pool
Before installation, check that the sealing nut (No. 8 + 20) is fully
tightened
The spotlights should be placed on the wall of the pool about 400-
700 mm away from the surface of the water (Fig. 1)
The procedure for attaching the housing to the pool wall depends on
whether the lights are for a concrete pool or a ready-made pool.
Concrete pool
To install underwater lighting in a concrete swimming pool , the
housing (No. 12) should be fixed into the wall of the swimming pool
(Fig. 2). Ensure that the cable outlet is on the upper side of the hous-
ing.
Ready-made pools
To install lighting in a ready-made pool, cut a circular hole with a di-
ameter of 270 mm (Fig. 2).
From the inside, insert the housing (No 12) with one of the sealing
rings (No 17.) attached on top. Fix the housing and the swimming
pool panel using S screws or bolts (not included). When the lining is
in position, fix the clamp (No 18) with the other sealing rings (No 17)
and with 16 screws included (No 19) (Fig, 3).
Ensure that the cable outlet stays on the upper side of the housing.
After installing the housing and the clamp, mount the under water
lighting in a ready made pool
to connect the light to the mains, pass the cable through the sealing
nut (4). Tighten the sealing nut until you can check that the cable
gives when you pull on it by hand.
Take the necessary precautions to ensure you leave 1.5 m of coiled
cable on the base of the underwater lighting (No.11) so you are able
to put the light on the edge of the pool, or you can remove it when
changing the bulb or during other necessary maintenance (Fig. 4).
Push the whole lighting components into the housing (Fig. 5).
Tighten the two M-6 x 70 screws (No 15) until the fixing bracket fits
securely on the inner wall of the housing (Fig. 7).
Summary of Contents for 060935
Page 30: ......
