manualshive.com logo in svg

Steelcase Avenir Panel Worksurface with Pedestal to the Floor, Manual

Share
Download
Steelcase Avenir Panel Worksurface with Pedestal to the Floor Manual Download Page 14

Page 14 of 18

939501051 Rev G

17

18

X

X

Installing a Curved Worksurface

The curved worksurface is equipped with (2) 
factory attaching plates.
Place curved worksurface onto cantilevered of 
floor support.  Loosen screws slightly to allow 
attaching plate adjustment.  Align slotted holes 
with holes in cantilevered or floor support.  
Now position straight worksurfaces on top of 
attaching plates while at the same time 
aligning attaching holes.
Next start all screws and leave loose.  Align all 
worksurfaces so that spacing is equal before 
tightning screws.  Refer to fig. A, section "X-X" 
below.
When a curved worksurface is assembled 
without an adjacent straight worksurface at one 
side, the attaching plate must be removed from 
the unused side and reassembled as shown in 
fig. B, section "X-X" below. 

Pedestal Glide Adjustment

ATTACHING PLATE

CURVED 
WORKSURFACE

CANTILEVERED OR 
FLOOR SUPPORTED

ATTACHING PLATE POSITION
(CURVED TOP TO STRAIGHT TOP)

ATTACHING PLATE POSITION
(CURVED TOP TO STRAIGHT TOP)

Section “X - X”

Summary of Contents for Avenir Panel Worksurface with Pedestal to the Floor



















Reviews:

No comments

Brands by name

Popular brands

Load more brands