manualshive.com logo in svg

Star Trac Elite CrossTrainer, Service Manual

Share
Download
Star Trac Elite CrossTrainer Service Manual Download Page 6

CrossTrainer Service Manual 

5                                        

  CrossTrainer Service Manual Rev A 620-7575 

Diagnostics -  Display Codes 

Display Codes 

Star Trac CrossTrainers perform a self-test at the beginning of every workout. If a problem is 
detected, a message displays before or after the workout, depending on the nature of the problem.

Key Down

 – One or more keys on the display panel are stuck in the “on” position for at least 10 

seconds. This can occur if a user presses keys before the system is turned on.  

Comm Lost

 – Communication between the Load Control Board (LCB) and the display are lost. This 

can occur if the display cable is not connected securely at install. 

Batt Low

 – Upper body actuator is commanded to work and the battery voltage is less than 5.7 volts.

Repl Batt

 – Upper body actuator is commanded to work and the battery voltage is less than 5.3 volts. 

Summary of Contents for Elite CrossTrainer












































Reviews:

No comments

Brands by name

Popular brands

Load more brands