manualshive.com logo in svg

Star Trac Elite CrossTrainer, Service Manual

Share
Download
Star Trac Elite CrossTrainer Service Manual Download Page 11

CrossTrainer Service Manual 

10                                        

  CrossTrainer Service Manual Rev A 620-7575 

Trouble Shooting -  Incorrect Model Setting 

The display electronics on the CrossTrainer can be configured to operate with many different models 
of Star Trac products. For them to operate properly, the correct model must be set in the 
Maintenance mode.

If the correct model is not set, the following may happen: 

x

  When the unit is powered up, the display will read “Pro Bike” (or Pro Stepper) in the level 

profile window. 

x

  The display will read “Start Pedaling” or “Start Stepping” instead of “Start Striding”.

x

  Also, some programs will not work when the keys are pressed. i.e. When pressing the Total 

Body program key, Warm Up program will start.

If you experience any of these symptoms, engage the Maintenance mode to correct the Model 
setting.

Engaging Maintenance Mode 

1.  Press and hold the

,

 and 

 keys together. 

2.  A beep will sound and the “MAINTENANCE MODE” will display momentarily in the information 

window.  

3.  Release all keys. “SERIAL NO XXXXX” will display in the information window.

4. Press the 

until the display reads “Model”. 

5. Press the 

until the correct setting shows.

x

  Pro CT = CrossTrainer Pro which has fixed upper body mechanism.  

x

  Elite CT = CrossTrainer Elite which has the adjustable upper body mechanism.  

6. Press 

 to save the setting and exit the maintenance mode.

7.  Test for functionality.  

Summary of Contents for Elite CrossTrainer












































Reviews:

No comments

Brands by name

Popular brands

Load more brands