manualshive.com logo in svg

Star Trac Elite CrossTrainer, Service Manual

Share
Download
Star Trac Elite CrossTrainer Service Manual Download Page 29

CrossTrainer Service Manual 

28                                        

  CrossTrainer Service Manual Rev A 620-7575 

Part Installation Procedure – Upper Crank Arm (cont.) 

4.  With one hand cupped over the e-clip, use a flat-head screwdriver to pop the e-clip off the 

upper crank pin.  Be careful not to lose the e-clip.

5.  Carefully slide the leg beam off of the upper crank pin. You may want to use your foot to 

support the lower end of the leg beam as you pull. Remove the shims and wavy washers from 
the crank pin and set them aside for re-use.

6.  Remove the plastic cap and retaining ring from the center of the upper crank arm. Completely 

remove both of the pinch bolts using a 5/16 (Allen) hex key.  

7.  Insert a ¾ inch cold chisel or a large flat-head screwdriver in the slot in the end of the upper 

crank arm and tap with a hammer to slightly spread open the end of the crank arm. The crank 
arm should easily slide off the main shaft assembly.

Summary of Contents for Elite CrossTrainer












































Reviews:

No comments

Brands by name

Popular brands

Load more brands