GENERAL INSTALLATION INSTRUCTIONS
CAUTION
This equipment is designed and sold for commercial
use only by personnel trained and experienced in its
operation and is not sold for consumer use in and
around the home nor for use directly by the general
public in food service locations.
All shipping containers should be checked for freight damage both visible and concealed.
This unit has been tested and carefully packaged to insure delivery of your unit in perfect
condition. If equipment is received in damaged condition, either apparent or concealed, a
claim must be made with the delivering carrier.
Concealed damage or loss - if damage or loss is not apparent until after equipment is unpacked,
a request for inspection of concealed damage must be made with carrier within 15 days. Be
certain to retain all contents plus external and internal packaging materials for inspection. The
carrier will make an inspection and will supply necessary claim forms.
INSTALLATION
Each machine has been properly wired and inspected at the factory for operation on the voltage
and type of current speci
fi
ed on the nameplate. Machines with a nameplate stamped 120V, are
equipped for operation on 120 volt 60 hertz AC single phase service and must be connected
to a separate 15 amp circuit with a 3 wire grounded, polarized receptacle. 230V models must
be connected to a 230V, 60Hz, AC single phase service.
Water hardness in some areas will cause scaling (lime scale buildup) in your equipment. This
scaling will coat the inside of the reservoir and waterlines of your Hot Food Humidity Cabinet.
Therefore, STAR Manufacturing recommends using distilled water for the prevention of scaling
in your equipment. This will prolong the life of your STAR equipment.
CAUTION
DO NOT CONNECT TO ANY
OTHER TYPE OF CURRENT
SOURCE OR THE MACHINE WILL
BE SERIOUSLY DAMAGED.
The guarantee of this machine covered by the
warranty card does not apply if an improper
installation has been made.
CAUTION
DO NOT BLOCK VENT HOLES ON TOP
OF THE CABINET.
5. Fill Light - This is used as a reminder during
start up. When the power switch is pushed on
the
fi
ll light will illuminate to remind the operator
to
fi
ll the reservoir. The
fi
ll light will go OFF
when the reservoir is
fi
lled to the maximum.
PIZZA SHELVES
UNIVERSAL SHELF
ON
OFF
POW
ER
MOD
E
-HOLD
TEM
PERATU
RE A
ND H
UMIDIT
Y PR
OGRAMMING:
TO S
ET D
IFFER
ENT
PRE
SET, OR
PRES
S
TO S
ET H
UMI
DITY
TO D
ISPLA
Y H
UMI
DITY
SETTIN
G
TO S
ET C
ABIN
ET
TEMP
ERAT
URE
FOR
THREE SEC
ONDS UN
TIL CU
RREN
T P
RESE
T
TO E
XIT P
ROGR
AM
FUNC
TION
FLAS
HES,
AND
THE
CABINE
T TE
MP
ERATU
RE IS
DISPL
AYED
MODE
SE
LE
CT
AND
-US
E
MODE
AND
-PR
ESS
-PRE
SS
-US
E
TO C
HAN
GE
THE
SE
TTING
FAH
RENHE
IT OR C
ELS
IUS S
ELEC
TION
:
TO T
OGGL
E THRO
UGH
PRE
SETS
MO
DE
SE
LECT
MODE
-PRES
S AND
HOLD
-PRES
S AN
D HOLD
THEN P
RESS
THEN
PRES
S
LIGH
TS WI
LL
T
UR
N
ON. FILL
RES
ERV
OI
R
UNT
IL
LIGH
TS
TUR
N OFF
.
WHEN THE
WA
TER L
EV
EL BE
CO
MES
LO
W, T
HE "
LO
W WA
TER
" AND
"
FILL
"
SELECT
P/S
3
P/
S
2
P/S 1
P/
S
6
P/S 5
P/S 4
PRES
ET S
ELECT
ION:
WA
TER
FIL
L IN
STRUCT
ION
S:
MOD
E
LOW WATE
R
FILL
PRETZEL RACK
FIGURE 1
TO MOTOR SHAFT
TO BOTTOM PIN
TO MOTOR SHAFT
TO BOTTOM PIN
TO SLOTS IN SIDE BRACKETS
INSERT HOLDING CLIP
THRU TOP INTO MOTOR SHAFT
ACCESSORY INSTALLATION
IL1028
IL1033
