Stanley SS28, Manual

Page: 7 / 32

7
ENGLISH (
Original Instructions)
V Volts Direct Current
A Amperes n
0
No-Load Speed
Hz Hertz Class II Construction
W Watts Earthing Terminal
min minutes Safety Alert Symbol
Alternating
Current
/min.
Revolutions or
Reciprocation per
minute
Date Code Position (Fig. B)
The Date Code, which also includes the year of
manufacture, is printed into the housing.
Example: 2018 XX XX
Year of Manufacture Package Contents
THE PACKAGE CONTAINS
1 1/3 Sander
1 Instruction manual
1 Warranty card
1 Service center list
♦ Check for damage to the tool, parts or accessories
which may have occurred during transport.
♦ Take the time to thoroughly read and understand this
manual prior to operation.
Description (Fig. A)
WARNING: Never modify the power tool or any
part of it. Damage or personal injury could result.
1. On/off switch
2.Lock-on button
3.Sanding Base
4.Paper clamp lever
ASSEMBLY AND ADJUSTMENT
WARNING: To reduce the risk of serious
personal injury, turn tool off and disconnect tool
from power source before making any
adjustments or removing/installing attachments or
accessories. Before reconnecting the tool, depress and
release the trigger switch to ensure that the tool is off. An
accidental start-up can cause injury.
Fitting sanding paper (Figure. A,B)
Warning! Never use the tool without a sanding paper or
accessory in place.
♦ Soften the sanding paper by rubbing its non-abrasive
side over the edge of a worktop.
♦ Release the sanding paper clamp levers (4).
♦ Place the paper onto the sanding base (3).
♦ Insert the edge of the sanding paper into the front
paper clamp as shown.
♦ Press the front paper clamp lever (4) downwards.
♦ While keeping a slight tension on the paper, insert the
rear edge of the paper into the rear paper clamp.
♦ Press the rear paper clamp lever (4) downwards.
USE
WARNING:Let the tool work at its own pace. Do
not overload.
Switching on and off
♦ To switch the tool on, press the on/off switch (1).
♦ For continuous operation, press the lock-on button (2)
and release the on/off switch.
♦ To switch the tool off, release the on/off switch. To
switch the tool off when in continuous operation, press
the on/off switch once more and release it.
Hints for optimum use (Figure. C)
♦ Do not exert too much pressure on the tool.
♦ Regularly check the condition of the sanding paper.
♦ Replace when necessary.
♦ It is better to sand along the grain of the wood.
♦ When sanding new layers of paint before applying
another layer, use extra fine grit.
♦ On very uneven surfaces, or when removing layers of
paint, start with a coarse grit. On other surfaces, start
with a medium grit. In both cases, gradually change to
a fine grit for a smooth finish.
♦ Consult your retailer for more information on available
accessories.
Residual risks
Additional residual risks may arise when using the
tool which may not be included in the enclosed safety
warnings. These risks can arise from misuse, prolonged
use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
♦ Injuries caused by touching any rotating/moving parts.
♦ Injuries caused when changing any parts, blades or
accessories.
♦ Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
♦ Impairment of hearing.
♦ Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
MAINTENANCE
Your STANLEY power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
♦ Regularly clean the ventilation slots in your tool using
a soft brush or dry cloth.
♦ Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.This
machine is not user-serviceable. If problems occur
contact an authorised repair agent.