Stanley NUA Electric User'S Manual & Installation Instructions Download

Page: 34 / 40

The method of connection to the mains electricity supply

must facilitate complete electrical isolation of the appliance,

by a multi-pole switch, having a contact separation of at least

3 mm on all poles.
The isolator should not be positioned immediately above the

cooker, but must be fitted within 2 metres of the appliance.
The isolator maybe separate from the connection point.
The mains connection point must be accessible within the

areas shown in

Fig. 16.1

for cable routing options.

Induction Hob

An additional,

separate single phase power supply

required. 230V ~ 50Hz, 13amp fused three pin plug electrical

supply.

16. Electrical connection

Fig. 16.1

WARNING: This appliance must be earthed.

This appliance is designed for the voltage stated on

the rating plate, which is situated behind the plinth

cover.

If the supply cord is damaged, it must be replaced

by the manufacturer, its service agent or similarly

qualified person to avoid a hazard.

For the cooker

Two seperate phase 13 AMP 230V or 3PH 400V minimum

16A per phase ~ 50 Hz fused electrical supply are required

adjacent to the appliance. External wiring to the unit must

be installed using the mains cable provided, in accordance

with the current wiring regulations and any local regulations

which apply. If the cable is shortened, new ferrules must be

fitted to the stripped conductors.

WORKTOP

0.9

metre

1.8

tre

450m

Cable point for 3m long 13A cable supplying induction hob.

Cable point for 3m long 13A cable supplying main cooker.

THE MAINS SUPPLY MUST BE WITHIN THE ZONES SHOWN. IF A RECESSED

COOKER CONNECTIONIS TO BE USED BEHIND THE APPLIANCE WITHIN THE

HATCHED AREA ALLOW A 5mm GAP AT THE REAR OF THE APPLIANCE.

THE MAINS SUPPLY MUST BE WITHIN THE ZONES SHOWN. IF A RECESSED

COOKER CONNECTION IS TO BE USED BEHIND THE APPLIANCE WITHIN

THE HATCHED AREA ALLOW A 5mm GAP AT REAR OF APPLIANCE.

Cable point for 3m long 13A cable supplying the two hotplates

Cable point for 3m long 13A cable supplying main cooker.

WORKTOP

0.9 metr

450mm M

1.8 metr

WORKTOP

DESN 517950

Summary of Contents for NUA Electric









































Search results

Summary of Contents for NUA Electric

Reviews:

Related manuals for NUA Electric

Brands by name

Popular brands

Stanley NUA Electric, User'S Manual & Installation Instructions

Search results

Summary of Contents for NUA Electric

Reviews:

Related manuals for NUA Electric

Brands by name

Popular brands