background image

19

WARNING NOTE:

Properly installed, operated and maintained this
stove will not emit fumes into the dwelling.
Occasional fumes from the de-ashing and re-
fuelling may occur. However, persistent fume emis-
sion is potentially dangerous and must not be toler-
ated. If fume emission does persist, then the follow-
ing immediate action should be taken:

(a) Open doors and windows to ventilate room.

(b) Let the fire out or eject and safely dispose of 

fuel from the stove.

(c)  Check for flue or chimney blockage and clean if

required.

(d)  Do not attempt to relight the fire until the cause

of the fume emission has been identified and 
corrected.  If necessary seek expert advice.

The most common cause of fume emission is flue-
way or chimney blockage.  For your own safety
these must be kept clean at all times.

FIRE SAFETY

To provide reasonable fire safety, the following
should be given serious consideration.

1. Do not over fire the stove.
2. Over-firing will also damage painted or enamel

finish.

3. Install a smoke detector in the room.
4. A conveniently located class A fire extinguisher to

contend with small fires resulting from burning 
embers.

5. A practical evacuation plan.
6. A plan to deal with a chimney fire as follows:-

(a) Notify the fire department.

(b) Prepare occupants for immediate evacua-

tion.

(c) Close all openings into the stove.

GLASS REPLACEMENT

(a) Open the firedoor fully.
(b) Remove the four corner screws and clips and 

carefully remove the broken glass.

(c) Clean the glass recess in the door.
(d) Replace the sealing rope in the door if 

necessary

(e) Tighten screws.
(f) Replace glass only with ceramic glass 5mm 

thick. (See Fig 24).

(d) While awaiting the fire department watch for

ignition to adjacent combustibles from over- 

heated flue pipe or from embers or sparks 

from the chimney.

Fig. 24

CO ALARM

The fitting of CO Alarms in the same room as the
appliance is a compulsory requirement under cur-
rent Building Regulations. For ROI an additional CO
Alarm must be fitted either inside each bedroom or
within 5 metres of the bedroom door, refer to
Building Regulations Part J. Further guidance on the
installation of a carbon monoxide alarm is available
in BS EN 50292:2002 and from the alarm manufac-
turers instructions.

Provision of an alarm must not be considered a
substitute for either installing the appliance 
correctly or ensuring regular servicing and
maintenance of the appliance and chimney 
system.

WARNING:-

If the CO Alarm sounds unexpectedly:-

1. Open Doors and windows to ventilate the 

room and then leave the premises.

2. Let the fire go out.

PROLONGED PERIODS OF NON USE

If the stove is to be left unused for a prolonged peri-
od of time then it should be given a thorough clean
to remove ash and unburned fuel residues.  To
enable a good flow of air through the appliance to
reduce condensation and subsequent damage,
leave the air controls fully open.

It is important that the flue connection, any appliance
baffles or throat plates and the chimney are swept
prior to lighting up after a prolonged shutdown 
period.

Summary of Contents for Lismore

























Reviews: