41
ENGLISh
Attaching Upper Handle (Fig. A, D)
1. Line up the holes on the bottom of the upper handle
4
with the holes on the top of the lower handle
5
. Take care
to not pinch or stress the cord.
NOTE:
Make sure the cord is located on the front of both
handles. If it is not it may result in the cord tangling and the
inability to easily store the mower.
2. From the outside of the upper handle
4
, slide the handle
lock levers
16
through the two handle holes. Repeat for the
opposite side.
3. From the inside of the upper handle loosely tighten a
knob
17
onto each handle lock lever
16
.
4. Rotate the upper handle
4
into its operating position. Take
care to not pinch or stress the cord.
5. Close the handle lock levers
16
securing the upper handle
into position.
NOTE:
If the connection between the handle and lever
is too tight or too loose, open the lever and adjust the
depth of the lever by turning the lever clockwise or
counterclockwise. Close it again until each lever stays
securely closed and the handle is secure and will not move.
Adjusting Handle Height (Fig. A, C)
The mower is shipped in storage mode. You will need to adjust
the handle to operating position before continuing.
1. To unlock the lower handle
5
from the storage position,
open the two handle height adjust levers
15
. The handle
height adjust levers
15
are located on both sides of the
lower handle
5
.
2. Raise the lower handle to the operating position. Take care
to not pinch or stress the cord.
3. Close the handle height adjust levers
15
, securing the
lower handle into position.
NOTE:
If the connection between the handle and lever
is too tight or too loose, open the lever and adjust the
depth of the lever by turning the lever clockwise or
counterclockwise. Close it again until each lever stays
securely closed and the handle is secure and will not move.
ASSEMBLY AND ADJUSTMENTS
DANGER: To reduce the risk of serious personal
injury, turn unit off and remove the safety key and
battery packs before making any adjustments or
removing/installing attachments or accessories.
An
accidental start-up can cause injury.
Grass Collection Bag (Fig. E)
DANGER:
Turn unit off and remove safety key and
battery packs.
1. Lift the rear door cover
9
, remove mulch plug
20
, and
place the grass collection bag
10
onto the mower so
the bag lugs
20
slide into the slots
21
on the inside
plastic surfaces of the handle brackets. Then lower the rear
door cover.
2. If installed, remove side discharge chute
14
and make sure
side flap
13
is fully down.
Adjusting Mower Height (Fig. G, H)
WARNING: Never attempt to adjust mower height
with the motor running.
The height of cut is adjusted by the cut height adjust lever
8
.
NOTE:
If you are not sure what height to cut at, begin mowing
with the cut height adjustment levers
8
positioned towards the
rear of the appliance and adjust the height down as needed.
To Set the Height of Cut
1. Pull the cut height adjustment lever
8
out of the locking
notch
23
.
2. Move the lever towards the rear of the appliance to raise the
height of cut as desired.
3. Move the lever towards the front of the appliance to lower
the height of cut as desired.
4. Push the cut height adjustment lever
8
into one of the
locking notches
23
to set the height.
5. Repeat for the other cut height adjustment lever
8
.
Mulching (Fig. A, E, F)
DANGER:
Turn unit off and remove safety key and
battery packs.
1. To operate mower in mulching mode, remove the grass
collection bag
10
.
2. Lift the rear door cover
9
and slide the mulch plug
20
fully
into the mower.
3. Be sure rear door cover is closed.
4. If installed, remove side discharge chute
14
and make sure
side flap
13
is fully down.
Side Discharge (Fig. A, F)
DANGER:
Turn unit off and remove safety key and
battery packs.
1. To operate mower in side discharge mode, remove the grass
collection bag
10
.
2. Be sure rear door cover
9
is closed.
3. Lift the side flap
13
and hook side discharge chute
14
onto
the mower.
4. Release the side flap and ensure the side discharge
chute
14
holds in place before turning mower on.
NOTE:
The rear door cover
9
is shaped in such a way that the
opening (at the bottom) cannot be completely closed off.
OPERATION
Instructions for Use
WARNING:
Always observe the safety instructions and
applicable regulations.
WARNING:
To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories.
An accidental
start-up can cause injury.
Summary of Contents for FATMAX SFMCMW2651
