Stanford Research Systems SR470 Operation Manual Download Page 64

Page: 64 / 64

2 – 28

Remote Operation

2.6.5

Communication Errors

Error Code

Meaning

170

Communication Error

A communication error was detected. This is re-
ported if the hardware detects a framing, or parity
error in the data stream.

171

Over Run

The input bu

ﬀ

er of the remote interface over-

ﬂowed. All data in both the input and output
bu

ﬀ

ers will be ﬂushed.

2.6.6

Other Errors

Error Code

Meaning

254

Too many errors

The error bu

ﬀ

er is full. Subsequent errors have

been dropped.

SR470 Shutter Controller

Distribution in the UK & Ireland

Lambda Photometrics Limited

Lambda House Batford Mill
Harpenden Herts AL5 5BZ
United Kingdom

E:   [email protected]
W:   www.lambdaphoto.co.uk
T: +44 (0)1582 764334
F:   +44 (0)1582 712084

Characterisation,
Measurement &
Analysis

Summary of Contents for SR470

































































Search results

Summary of Contents for SR470

Reviews:

Related manuals for SR470

Brands by name

Popular brands

Stanford Research Systems SR470, Operation Manual

Search results

Summary of Contents for SR470

Reviews:

Related manuals for SR470

Brands by name

Popular brands