manualshive.com logo in svg

Stamina X-Flex GYM 50-0175A, Owner'S Manual

Share
Download
Stamina X-Flex GYM 50-0175A Owner'S Manual Download Page 9

ASSEMBLY INSTRUCTIONS

9

STEP 9

Attach the 

FRONT STABILIZER(10)

 onto the 

SUPPORT FRAME(9)

 with 

BOLTS(3/8" x 3/4")(68)

and 

WASHERS(3/8")(78).

Attach the 

SUPPORT FRAME(9)

 onto the 

RAIL(8)

 with 

BOLTS(3/8" x 1")(69), BOLT(3/8" x 3/4")

(68), WASHERS(3/8")(78)

 and 

NYLOCK NUTS(3/8")(81).

STEP 10

Attach the 

SEAT CUSHION(15)

 onto the 

SEAT CARRIAGE(12)

 with 

BOLTS(3/8" x 3/4")(68)

 and

WASHERS(3/8")(78).

  Screw the 

SPRING PIN(25)

 onto the 

SEAT CARRIAGE(12).

  Pull out the

SPRING PIN(25)

 and then slide the 

SEAT CARRIAGE(12)

 onto the 

RAIL(8).

Attach the back end of the 

RAIL(8)

 onto the 

UPRIGHT(3)

 with 

BOLT(3/8" x 4 1/4")(75), WASHERS

(3/8")(78),

 and 

NYLOCK NUT(3/8")(81).

  Lock the 

RAIL(8)

 in position with the 

L PIN(3/8" x 6 3/8")

(45).

STEP 11

Attach the 

BACK CUSHION(16) 

onto the 

BACK SUPPORT(13)

 with 

BOLTS(3/8" x 3/4")(68) 

and

WASHERS(3/8")(78).  

Attach the 

BACK SUPPORT(13) 

onto the 

SEAT CARRIAGE(12)

 with the 

L

PIN(3/8" x 8 5/8")(46).

Summary of Contents for X-Flex GYM 50-0175A























Reviews:

No comments

Brands by name

Popular brands

Load more brands