background image

BEFORE YOU BEGIN

4

  Thank you for choosing the 

1215 Orbital Rower.

We take great pride in producing this quality product
and hope it will provide many hours of quality exercise
to make you feel better, look better and enjoy life to
its fullest.
  Yes, it's a proven fact that a regular exercise
program can improve your physical and mental
health. Too often, our busy lifestyles limit our time
and opportunity to exercise. The

 1215 Orbital Rower

provides a convenient and simple method to begin
your assault on getting your body in shape and
achieving a happier and healthier lifestyle.
   Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
  Read this manual carefully before using the 

1215

Orbital Rower.

   Although Stamina constructs its products with the
finest materials and uses the highest standards of
manufacturing and quality control, there can
sometimes be missing parts or incorrectly sized
parts. If you have any questions or problems with
the parts included with your 

1215 Orbital Rower,

please do not return the product. Contact us FIRST!
   If a part is missing or defective, please call us toll
free at 1-800-375-7520 (in the U.S.). Our Customer
Service Staff is available to assist you from 7:30 A.M.
to 5:00 P.M. (Central Time) Monday through Thursday
and 8:00 A.M. to 3:00 P.M. (Central Time) on Friday.
   If you would like to contact us online, go to our
website at www.staminaproducts.com and access the
Customer Service section.
   Be sure to have the name and model number of
the product available when you contact us.

THE FOLLOWING TOOLS ARE REQUIRED FOR ASSEMBLY :

 Phillips Screwdriver

 Adjustable Wrench

 Adjustable Wrench

Rear

Support

Endcap

Seat

Left Handlebar

Shock

Locking Knob

Left Base Frame

Foam Grip

Pedal Strap

Meter

Pedal

Endcap

Shock

Locking Knob

Right Base Frame

Center Beam

Pull Pin

Foam Grip

Right
Handlebar

Pivot Support

Warning

Label

Shock Decal

Shock Decal

Summary of Contents for Orbital Rower 1215























Reviews: