background image

OPERATIONAL INSTRUCTIONS

11

CAUTION: 

The shocks get HOT after a few minutes of use. To avoid burns, do not touch the shock until 

it has time to cool.

NOTE: 

Tighten 

LOCKING KNOBS(13)

 securely before using the 

1215 Orbital Rower.

A.

B.

LOAD ADJUSTMENT

The resistance of the shocks can be adjusted by sliding the 

TENSION ADJUSTERS(12)

 to change the 

position on the 

HANDLEBARS(8, 9).

 The lowest position will provide the lowest resistance, the upper 

position will provide the higher resistance.

Loosen the 

LOCKING KNOB(13)

 and slide the 

TENSION ADJUSTER(12)

 to aspired position. Tighten the 

 

LOCKING KNOB(13)

 after adjusting. Use the number marks on the 

HANDLEBARS(8, 9) 

to help set the 

TENSION ADJUSTER(12)

 at the same height on both sides.

TO ADJUST THE REAR SUPPORT(16)

Pull out the 

PULL PIN(17)

 from the 

SUPPORT BRACKET(15).

 Fold the 

REAR SUPPORT(16)

 forward, 

then you can set the 

1215 Orbital Rower

 flat on the floor. Lock the 

SUPPORT BRACKET(15)

 in the flat 

position by inserting the 

PULL PIN(17)

 back into the 

SUPPORT BRACKET(15).

 Refer to illustration B.

The seat can slide freely when the 

1215 Orbital Rower

 is in the flat position. In the incline position as shown 

in illustration A, there will be more resistance as you slide backward, less resistance as you slide forward.

Summary of Contents for 35-1215B























Reviews: