SRAM ROAM 50 Service Manual Download Page 29 | Manualshive

Page: 29 / 40

background image

29

ROAM 60/50 & RAIL 50 Rear Hub Bearing Replacement

Lightly grease the bearing bores.

Install one of the Short Installation Cylinders into a vise. Install a

new bearing onto the long end of the axle with the red seal facing

away from the axle.

Install the long end of the axle into the Short Installation Cylinder.

Firmly press down on the axle to seat the bearing onto the axle.

Install the drive side of the hub onto the axle and bearing.

15

16

Short Installation Cylinder

17

18

«
...
27
28
29
30
31
...
»

Summary of Contents for ROAM 50









































Reviews:

No comments

Related manuals for ROAM 50

AVID DISC BRAKES

Brand: Avid Technology Pages: 2

Brand: Rose electronics Pages: 2

Brand: CD Pages: 25

Brand: Btwin Pages: 18

Brand: GLOBBER Pages: 20

Brand: GLOBBER Pages: 74

Brand: Echowell Pages: 2

Brand: Qelectric Pages: 14

Brand: RAYVOLT Pages: 18

Brand: Xalingo Pages: 2

BT C01.340.UART

Brand: BAFANG Pages: 34

Brand: DAHON Pages: 22

Sonic Bike Fastmute

Brand: Ge-Tectronic Pages: 4

RACE ATTACK RA-1

Brand: Rose electronics Pages: 4

Brand: Lacros Pages: 15

Brand: SmartHalo Pages: 40

Brand: Sachs Pages: 8

Brand: KEEWAY Pages: 218

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands