manualshive.com logo in svg

SPX Pearpoint Flexiprobe P340, Service Manual, Page: 51 / 60

Share
Download
SPX Pearpoint Flexiprobe P340 Service Manual Download Page 51

 

 

Copyright 2012 Radiodetection Ltd.

– SPX Corporation. All rights reserved. Radiodetection is a subsidiary of SPX Corporation. 

This document may not be copied, reproduced, transmitted, modified or used, in whole or in part, without the prior written consent of Radiodetection 
Ltd.  We reserve the right to alter or amend any published specification without notice.

 

   

 

 

 

Page 51 of 59

 

 

Slide the rod connector up the rod 
as shown followed by the thrust 
washer, the clamp ring (Olive) 
and the clamp nut. 
 

 

Slide the thrust washer 

item 10 

up to the shoulder of the 
connector. 
Line up the grub screw hole and 
the screen wire hole of the potting 
collar. 
Apply Loctite 243 to one off M2.5 
x 4 grub screw 

item 14 

and screw 

down on to the screen wire in 
the potting collar. 

IMPORTANT: DO NOT OVER-
TIGHTEN THE GRUB SCREW 

 

 

 

If a suitable torque spanner is 
available, carry out the following 
procedure, otherwise tighten the 
connector clamp nut using a 
17mm open-ended spanner with 
a 14mm open-ended spanner on 
the connector body until the nut 
just touches the connector body. 
 
Use a fixed 14mm spanner and a 
17mm torque spanner for the next 
part of the process. 
 

M2.5 x 4 Grub 
screw 

Summary of Contents for Pearpoint Flexiprobe P340





























































Reviews:

No comments