manualshive.com logo in svg

SPX Pearpoint Flexiprobe P340, Service Manual, Page: 37 / 60

Share
Download
SPX Pearpoint Flexiprobe P340 Service Manual Download Page 37

 

 

Copyright 2012 Radiodetection Ltd.

– SPX Corporation. All rights reserved. Radiodetection is a subsidiary of SPX Corporation. 

This document may not be copied, reproduced, transmitted, modified or used, in whole or in part, without the prior written consent of Radiodetection 
Ltd.  We reserve the right to alter or amend any published specification without notice.

 

   

 

 

 

Page 37 of 59

 

6.

 

P342 or Gatorcam 4 Midi Reel (60M/200’ or 120M/400’)        10/RP2809

  

 

 

Rod Camera-End Retermination 
 
Materials required, one of:- 
 

Rod Re-termination Kit (Full) 

10/RP2809    

(replaces all parts) 

Rod Re-termination Kit (Partial)  10/RP2809-2  

(re-uses original slipring PCB) 

Rod Re-termination Kit (Basic) 

10/RP2809-3  

(re-uses slipring PCB, rod connector, collet                  

.    

                                                                                  and Shroud nut) 

Slipring Re-termination Kit   

10/RP2809-4  

(slipring assembly only, includes circlip) 

 
See Bill-of-materials and drawings later in this chapter to confirm what you need. 
 
These instructions detail the re-termination procedures for both the P342 and GatorCam4 Midi 
60m

/200’ and 120m/400’ reels. Ensure that you read and understand these instructions in full 

before proceeding. 
 
There are two versions of the P332 rod termination, version 8A and version 9. 
The P342 rods use only the version 9 termination. 
 
They can be identified by checking the clamp nut (8A)/taper nut (9). 
The clamp nut of version 8A has two flats and the taper nut of version 9 has a hexagonal head. 
  
 

Discontinued version 

 

1) Shroud nut, 2) clamp nut, 3) thrust washer, 4) connector clamp ring (olive), and 5) rod 

connector. 

 

 

Current version  

 

 

The Bill of Materials and General Assembly drawings are at the end of this section. 

 

Summary of Contents for Pearpoint Flexiprobe P340





























































Reviews:

No comments