manualshive.com logo in svg

SPX Pearpoint Flexiprobe P340, Service Manual, Page: 10 / 60

Share
Download
SPX Pearpoint Flexiprobe P340 Service Manual Download Page 10

 

 

Copyright 2012 Radiodetection Ltd.

– SPX Corporation. All rights reserved. Radiodetection is a subsidiary of SPX Corporation. 

This document may not be copied, reproduced, transmitted, modified or used, in whole or in part, without the prior written consent of Radiodetection 
Ltd.  We reserve the right to alter or amend any published specification without notice.

 

   

 

 

 

Page 10 of 59

 

 

 
Cut the end of the rod squarely with the 
junior hacksaw. 
 

 

Slide the rear cover over the end of the 
Rod followed by the new 6mm O-ring. 
Push back out of the way. 
 

 

Score through full thickness of the outer 
sheath at 60mm from the end of the rod, 
taking care not to cut into the inner foil 
layer.   
 
Use suitable rotary cable stripping tools.   
 
(NOTE: we have found scalpels to be 
unsuitable and dangerous for this task.  
Do not use them) 
 

 

 
 

 
 

 

New 6mm O-ring 

Rear 
Cover 

Summary of Contents for Pearpoint Flexiprobe P340





























































Reviews:

No comments