10
11
OPERATING INSTRUCTIONS - REMOTE
Operating Instructions
COOL operation
- Press the MODE button until “COOL” indicator light illuminates.
Unit will run under auto-fan speed.
- Press the (+) or (-) buttons to set desired room temperature.
- Fan speed can be set/changed with remote.
DRY (dehumidify) operation
- Press the MODE button until “DRY” indicator light illuminates.
- Under this mode, you cannot select a fan speed or adjust the temperature.
- Keep windows and doors closed for the best dehumidifying effect.
- Do not put the duct to window.
FAN operation
- Press the MODE button until “FAN” indicator light illuminates.
The unit will run under auto-fan speed.
- Temperature cannot be set under this mode.
- Fan speed can be set/changed with remote.
- Do not put the duct to window.
SLEEP operation
This feature can only be activated by the remote control. Please refer to next section.
OPERATING INSTRUCTIONS - CONTROL PANEL
Fig.19
Adjust
manually
Adjust
manually
OTHER FEATURES
Auto-Restart
If the unit breaks off unexpectedly due to power cut, it will
restart at previous function when power resumes.
Wait 3 minutes before resuming operation
After the unit has stopped (or powered off), there will be a
3-minute delay before unit will start up again. This is to protect
the compressor. Operation will automatically resume after
3 minutes.
Air Flow Adjustment
The louvers can be adjusted manually. (Fig 19)
- Do not place or hang any heavy objects on the louver.
- Keep the louver fully opened during operation.
HANDLING THE REMOTE CONTROLLER
Location of the remote controller
Use the remote controller within a distance of 8m (26 ft) from the appliance,
pointing it towards the receiver.
When setting the timer, the remote will automatically transmit signal to the
unit at the specied time.
Note: if remote is kept in a position that hinders proper signal transmission,
a time lag of up to 15 minutes may occur.
CAUTIONS
- The air conditioner will not respond if curtains, doors or other barriers block the signal from the
remote controller to the unit.
- Prevent any liquid from coming in contact with the remote controller.
- Do not expose the remote controller to direct sunlight or heat.
- If the infrared signal receiver on the unit is exposed to direct sunlight, the air conditioner may
not respond. Close curtains/blinds to block sunlight from falling on the receiver.
- If other electrical appliances react to the remote controller, move those appliances if possible.
Installing / Replacing Batteries.
The remote controller is powered by two AAA
batteries (not included). The batteries are housed
in the back of the remote, protected by a cover.
1. Remove the cover by pressing down and sliding
off (according to arrow direction).
2. Remove old batteries and insert new batteries,
placing the (+) and (-) ends correctly.
3. Replace cover by sliding it back into position.
After replacing batteries, set the clock on the remote
controller (refer to page 14).
CAUTION
- Do not mix old and new batteries of a different type.
- Remove batteries if the remote controller is not to be used for extended period of time. Battery
leakage may occur and damage the remote.
- Keep the remote controller away from all liquids.
- Protect the remote controller from high temperatures and direct sunlight.
- Keep controller away from EMI (Electro-Magnetic Interference) supplied by other appliances.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult an experienced technician for help.
Fig.20
Fig.21
