SpringWell CF+ Page 2 Setup And Installation Manual Download

Page: 2 / 14

Setup And Installation

System Contents

Carbon Filter

Tank (CF+)

Conditioner

Tank (FS+)

Pre-Filter

Gasket and Lube

Spanner

Wrench

Sediment

Filter

Mounting

Bracket

Recommended Supplies

Primer and Cement

1.5-inch Tee

Connector (Slip) (x2)

1 Roll Plumbers

Tape

1.5-

inch PVC Pipe (10’ used in this

manual)

1.5-Inch PVC Shut Off

Valves (x3)

System Configuration

Water Source

From Outside Home

Filtered and Softened

Water Into Home

(1) Water from your

source will begin by

entering the Pre-Filter

(2) The Carbon Filter

(CF+) will be the second

tank and will remove

chemicals such as

chlorine

(3) The Softener (FS+) will

be the third tank and will

neutralize any remaining

particulate

Hose Bib

Assembly (2)

1.5-inch Elbow

Connector (Slip) (x8*)

1.5-inch Adapter (Slip

x Thread) (x6)

Questions? Call (800)-589-5592

* The quantities are suggestions. Your system configuration may vary depending on installation area.

CSF+ Whole House Filter/Salt Free Softener

Summary of Contents for CF+















Search results

Summary of Contents for CF+

Reviews:

Related manuals for CF+

Brands by name

Popular brands

SpringWell CF+, Setup And Installation Manual

Search results

Summary of Contents for CF+

Reviews:

Related manuals for CF+

Brands by name

Popular brands