SpringWell CF+ Setup And Installation Manual Download

Page: 10 / 14

Installing the Pre-Filter

This step will require the materials listed below

Prepped Pre-Filter

Housing

39) Note: Plumbers tape will
need to be applied to all PVC
threads during the installation.

40) Install a PVC adapter onto
one side of the Pre-Filter
Housing. Fully tighten.

41) Repeat on the other side. Fully
tighten.

42) Identify the optimal area to
secure the mounting bracket
and mark for pre-drilling. The
bracket should mount to a stud
due to weight.

43) Pre-drill the holes for the

mount using the 3/16” drill bit.

Mounting

Bracket

1.5-inch Adapter (Slip x

Thread)(x2)

Plumbers Tape

44) Use 4 of the provided bolts and
washers to secure the mounting
bracket in place using a half inch
socket.

Drill with 3/16” drill bit

1/2” Socket and

Ratchet

1.5-inch Elbow

Connector (Slip) (x2*)

1.5-inch PVC Pipe (Cut to fit)

Questions? Call (800)-589-5592

* The quantities are suggestions. Your system configuration may vary depending on installation area.

CSF+ Whole House Filter/Salt Free Softener

Summary of Contents for CF+















Search results

Summary of Contents for CF+

Reviews:

Related manuals for CF+

Brands by name

Popular brands

SpringWell CF+, Setup And Installation Manual

Search results

Summary of Contents for CF+

Reviews:

Related manuals for CF+

Brands by name

Popular brands