background image

Mounting the Paint Hopper

1. Align the bottom of the paint hopper with the threaded

inlet valve on the paint pump block.

2. Turn the paint hopper clockwise to thread it onto the inlet

valve. Continue to turn the paint hopper until it is secure
on the inlet valve.

3. Place the filter screen into the bottom of the paint hopper

and snap it in position.

Attaching the Return Tube

1. Make sure that the motor switch is turned to OFF. 
2. Screw the return tube fitting found in the literature set into the

return tube port on the side of the pump and tighten firmly by
hand.

3. Place the straight end of the return tube into the return

tube fitting.

4. Thread the nut on the return tube onto the return tube

fitting and tighten until the return tube is secure.

5. Place the hook end of the return tube into the hole in the

paint hopper cover.

SPRAY

PRIME

PRIME

Return Tube

Paint Hopper Cover

Return Tube Fitting

Return Tube

SPRAY

PRIME

NOTE: Do not over-tighten. Hand-tighten only.  Some

threads will be visible even when fully
tightened.

NOTE: Make sure the threads are straight and the

hopper turns freely on the inlet valve.  Do not
cross-thread.

Priming the Pump

1. Turn the pressure control knob counterclockwise to its 

lowest pressure setting.

2. Turn the PRIME/SPRAY knob to PRIME.
3. Turn the motor switch to ON.
4.  Turn the pressure control knob clockwise to between half

and full pressure.  You should see the paint move through
the suction tube to the pump.  Let the unit prime 1 to 2
minutes after paint begins to flow through the return tube.

Always reduce the pressure to zero before changing the
position of the priming knob.  Failure to do so may cause
damage to the paint pump diaphragm.

If the pressure control knob is reduced to zero and the
PRIME/SPRAY knob is still on SPRAY while the sprayer is
operating, there will be high pressure in the hose and
spray gun until the priming knob is turned to PRIME or
until the spray gun is triggered to relieve the pressure.

CAUTION

CAUTION

SPRAY

PRIME

PRIME

SPRAY

PRIME

PRIME

PRIME/SPRAY Knob

Pressure Control Knob

© SprayTECH Corporation.  All rights reserved.

7

English

Summary of Contents for ED655













































Reviews: