background image

45

Note that in dry areas in particular, static electricity can interfere with unit operation 

and shock people. To discharge static electricity from your body, touch something 

else before touching metal on the product.

8. GUIDELINES fOR EXERCISE

HOW HARD SHOULD I EXERCISE?

Studies show that to benefit from aerobic exercise, people need to maintain a certain 

heart rate during their workouts. Your heart rate training zone depends on your age 

and fitness level.

The darkened area in the chart to the right 

represents the recommended heart rate 

training zone for people of various ages. 

It was calculated by taking 220 minus age 

in years, multiplied by 65% and 80%. The 

area between those values is the heart rate 

training zone.

CAUTION: Heart rate training zones are 

generalizations and may not suit every 

person. Always check with your physician 

to understand what heart rate goal would 

be appropriate for you.

HOW LONG SHOULD I EXERCISE?

The duration of your workout must depend on your fitness level. In general, it is 

recommended that you maintain a heart rate within your training zone for at least 

15 to 20 minutes to experience the benefits of aerobic exercise.  Beginners should 

always start out slowly and gradually increase the duration and intensity of their 

workouts. As your fitness level improves, you will be able to maintain a heart rate 

within the training zone for longer periods of time.

When you begin your workout, use the first several minutes to warm up. Then slowly 

increase the intensity of your workout to bring your heart rate into your training zone. 

At the end of your workout, gradually decrease your workload. Then exercise lightly 

to cool down.

HOW OfTEN SHOULD I EXERCISE?

Research indicates that to achieve the greatest benefit, people should exercise 

three to five times per week. It is important to allow sufficient time, at least 24 hours, 

for your body to recover after exercise.

HE

 

Summary of Contents for T675
























































Reviews: