pushing on the removing button and put it away
in the compartment. Empty the device from all
liquid. Unplug the outlet from the wall.
Note: never let the device on the “on” position
when not in use. The water pressure will keep on
form and may damage the device. Always set the
“on/off” button from your water jet and the base
on the “off” position (O) when the device is not
in use.
You can
also use the
interdental brush head (with
integrated water jet) which
combines brushing and jet
efficiency.
This tool allows a good oral
hygiene, even in the hard to
reach area.
• TOOThbrUsh
Connecting and Maintenance
The cord of the base can be plug in any alterna-
ting current 220-240 volts (~) including the sha-
ver outlets. Place the toothbrush on the charging
base. When charging the red light indicator goes
on. The power pack may become hot when char-
ging. It is not affecting its functioning, overload is
excluded. In order to keep your toothbrush power
full; always put it back on its base.
Before using the appliance for the first time and
to protect the life of the battery, we recommend
to proceed as mentioned below:
1 – Charge the battery entirely for at least 16
hours prior to use.
2 – We recommend that you run the battery
flat by putting on the toothbrush until it stops
automatically (around 20-25 min before dischar-
ging).
The toothbrush has a timer for 2 minutes. To run
the battery flat entirely you need to launch the
program several times.
3 – Then fully charge the battery for at least 16
hours.
This procedure “charging/recharging” must be
done each 6 months.
N.B: when the battery starts running flat, the
toothbrush stops automatically to avoid batteries
to be fully discharged. All you need is plug the
device back on the base to recharge.
After operating the “charging /recharging” step
mentioned in the previous paragraph, you can
start using the toothbrush.
- Screw the brush head on the toothbrush.
- Before the first use of a brush head, carefully
rinse the brush head.
- Put your usual toothpaste on the brush
head.
- Rinse your mouth before brushing.
- To avoid spillage: Place the brush at an angle
to your teeth, then put the toothbrush on (button
on the handle of the toothbrush while you’re at a
lower speed - the first blue LED light).
- Pass the brush on your teeth from top to
bottom. Guide it along the inner and outer faces
also taking care to clean the gums. It is not
necessary to press hard the brush on your teeth.
Clean the sides and surfaces of your teeth..
- If you want to upgrade to a higher speed pres-
sing of the button on the handle of the toothbrush
(turbo speed - 2 blue LED are lit) and then to go
to massage press once again (a single blue LED
lit top of the brush).
- To stop the toothbrush again press the button
(all LED off).
- To fully remove dental plaque, the timer allows
you to brush your teeth for 2 min.
- Carefully rinse your mouth after brushing.
- During the first use, your gums may bleed a
little particularly if they are sensitive. After few
days the bleeding should stop. If your gums keep
bleeding after 15 days, we recommend you to
consult your dentist.
The efficient way to clean your teeth is to gently
run the brush over from one tooth to another,
without pressing.
The shape of the brush is changing with use,
which depends on the personal way of use of
the brush. This misshapenness has no impact
on the brush efficiency. However do not forget
to change the brush head as soon as a manual
toothbrush.
- After using the toothbrush, rinse carefully the
head brush.
- Put the toothbrush back on the charging base.
ENVIRONMENT FRIENDLY DISPOSAL
Your appliance contains valuable materials which
can be recovered or recycled. Please leave it at
a collection point as listed by your local authority.
CE : (2004/108/CE) – (2006/95/CE)
Rohs (2002/95/EC) - IPX7