SPM Machine Guard MG4-REF11A Instruction Manual Download | Manualshive

Page: 7 / 32

background image

Machine Guard MG4-REF11 A

5

SPM Instrument AB

• Box 504 • SE-645 25 Strängnäs • Sweden

Technical data are subject to change without notice.

Tel +46 152 225 00 • Fax +46 152 15075 • [email protected] • www.spminstrument.com

ISO 9001:2000 certified © SPM 2017-09. 71947 B

Mechanical installation

The MG4-REF11A is designed for wall mounting. It is fastened with 4 screws, the screw hole di-
ameter is 4 mm.

If possible, do not mount the unit against vibrating machine parts. The max. continuous vibration
level should not exceed 5 mm RMS.

The casing material is polycarbonate/PVC, dimensions 200 x 144 x 77 mm. The casing is classed
IP65. The cable inlet M12 for vibration measuring cable is tight for cable diameters 3 to 6.5 mm.
The cable inlet Pg11 is tight for cable diameters 5.5 to 10 mm.

The temperature range of the MG4-REF11A is 0 to 50 °C (32 to 122 °F).

The maximum length of the transducer cables is 100 m for SPM shock pulse transducers type 42000.

«
...
5
6
7
8
9
...
»

Summary of Contents for Machine Guard MG4-REF11A

































Reviews:

No comments

Related manuals for Machine Guard MG4-REF11A

Brand: OfiTE Pages: 24

Brand: Magnetic Instrumentation Pages: 63

Brand: Accurate Logic Pages: 50

Acuvim-L Series

Brand: AccuEnergy Pages: 188

Brand: VAMP Pages: 78

Brand: Wagner Meters Pages: 17

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 72

Brand: Yamaha Pages: 5

Brand: Yamaha Pages: 16

Brand: Yamaha Pages: 8

Brand: Yamaha Pages: 7

Brand: Yamaha Pages: 60

GranTouch Digital Grand Piano

Brand: Yamaha Pages: 19

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 29

Brand: Yamaha Pages: 47

Brand: lanry Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands