SPM Machine Guard MG4-REF11A Instruction Manual Download

Page: 30 / 32

SPM Instrument AB

• Box 504 • SE-645 25 Strängnäs • Sweden

Technical data are subject to change without notice.

Tel +46 152 225 00 • Fax +46 152 15075 • [email protected] • www.spminstrument.com

ISO 9001:2000 certified © SPM 2017-09. 71947 B

Technical specifications

General

Vibration monitoring:

1 channel

Shock pulse monitoring:

1 channel

Analog outputs (4):

4 - 20 mA analog signal, selective range, no galvanic separation

Main relay (1):

250 V AC, 5A, 1250 VA

Secondary relays (4):

125 V AC, 1A, 60 VA / 150 V DC, 1A, 30 W

Power supply:

230 V AC, 115 V AC ±10% *

Power consumption:

max. 6 VA

Operating temperature range: 0 to 50 °C (32 to 122 °F)
Relative humidity:

max. 95%

Altitude:

up to 2000 m

Casing:

polycarbonate/PVC, IP65

TNC connector:

silver plated brass, 10 to 15 μ

Display screen:

LCD, 4 x 16 characters, back-lighted

Status display:

green, yellow, red LED

Dimensions:

200 x 144 x 77 mm

Weight:

1140 g

Machine Guard MG4-REF11A

* Please note: The type of power supply is selected on ordering. It is factory set and cannot be
changed by the user. Please check the unit label for data.

Summary of Contents for Machine Guard MG4-REF11A

































Search results

Summary of Contents for Machine Guard MG4-REF11A

Reviews:

Related manuals for Machine Guard MG4-REF11A

Brands by name

Popular brands

SPM Machine Guard MG4-REF11A, Instruction Manual

Search results

Summary of Contents for Machine Guard MG4-REF11A

Reviews:

Related manuals for Machine Guard MG4-REF11A

Brands by name

Popular brands