Spektrum NX8 Instruction Manual Download

Page: 6 / 54

SPEKTRUM NX8 • TRANSMITTER INSTRUCTION MANUAL

TRANSMITTER FUNCTIONS

Function

Elevator Trim (Mode 2, 4)

Throttle Trim (Mode 1, 3)

R Trimmer

R Knob

Switch E

Switch H

Switch G

Switch F

Throttle Tension Adjustment

Throttle Ratchet Adjustment

(Mode 1, 3)

Gimbal Travel Limiter Access

Panel

Mode Change Screw

Function

Throttle/Aileron Stick (Mode 1)

Elevator/Aileron Stick (Mode 2)

Throttle/Rudder Stick (Mode 3)

Elevator/Rudder Stick (Mode 4)

Left/Right Gimbal Stick

Tension Adjustment

Up/Down Gimbal Stick

Tension Adjustment

Gimbal Travel Limiter Access

Panel

Aileron Trim (Mode 1, 2)

Rudder Trim (Mode 3, 4)

Neck Strap Mount

WiFi Indicator

Scroll wheel

Charge Indicator

LCD

Function

Function Button

Back Button

Clear Button

Speaker

Rudder Trim (Mode 1, 2)

Aileron Trim (Mode 3, 4)

Throttle Tension Adjustment

Throttle Ratchet Adjustment

(Mode 2, 4)

Gimbal Travel Limiter Access

Panel

Mode Change Screw

Elevator/Rudder Stick (Mode 1)

Throttle/Rudder Stick (Mode 2)

Elevator/Aileron Stick (Mode 3)

Throttle/Aileron Stick (Mode 4)

Function

Left/Right Gimbal Stick

Tension Adjustment

Up/Down Gimbal Stick

Tension Adjustment

Gimbal Travel Limiter Access

Panel

Switch D

Switch B

Switch A

Switch C

L Trimmer

Elevator Trim (Mode 1, 3)

Throttle Trim (Mode 2, 4)

On/Off Switch

Antenna

The transmitter comes with a thin, clear plastic film applied to some

front panels for protection during shipping. Humidity and use may

cause this film to come off. Carefully remove this film as desired.

11
12

13
14

30
29

Summary of Contents for NX8























































Search results

Summary of Contents for NX8

Reviews:

Related manuals for NX8

Brands by name

Popular brands

Spektrum NX8, Instruction Manual

Search results

Summary of Contents for NX8

Reviews:

Related manuals for NX8

Brands by name

Popular brands