SpeedEPart LST42H Manual Download Page 9 | Manualshive

Page: 9 / 36

background image

9

STEP 7: (SEE FIGURE 7)

• Attach the cable bracket (6) to the double hole in the

clutch frame as shown, using a 5/16" x 3/4" carriage
bolt (D) and a 5/16" nylock nut (Y). Place the bolt in
the front hole of the bracket and in the end of the hole
closest to the pulley.

Do not tighten yet.

FIGURE 7

FIGURE 9

STEP 9: (SEE FIGURE 9)

• Using lower set of holes attach each rear pulley frame

bracket to the inside of the clutch frame using two
5/16" x 3/4" hex bolts (D), 5/16" washers (Q), and
5/16" nylock nuts (Y).

Use upper set of holes for

Husqvarna TS200 with dual pedals

.

• Using lower set of holes attach each front pulley frame

bracket to the inside of the clutch frame using two
5/16" x 1" hex bolts (C), four 5/16" washers (Q), and
two 5/16" nylock nuts (Y).

Use upper set of holes for

Husqvarna TS200 with dual pedals

.

THIS SECTION IS FOR TRACTORS WITH A
MANUAL ATTACHMENT CLUTCH

If your tractor has an electric attachment clutch go to
step 14 on page 11.

FIGURE 10

STOP

Did you select the correct drive belt for your
tractor? Using the wrong length belt may
cause premature bearing or belt failure.

STEP 10: (SEE FIGURE 10)

• Two different length drive belts are included with your

snow thrower. Use the longer, 56" drive belt (

#48138

)

on tractors with manual attachment clutches.

• Slightly loosen the hex bolt next to the flat idler pulley.

Install the drive belt down between the hex bolt and the
flat idler pulley with the flat side of the belt against the
pulley. Retighten the hex bolt.

• Loop the belt around the large v-pulley, placing it

between the v-pulley and the hex bolt next to the pulley.
Place the belt to the inside of the other flat idler pulley.

FIGURE 8

STEP 8: (SEE FIGURE 8)

• Attach the pulley (22) (long end of hub facing down)

and the large 3/8" spacer (23) to the clutch frame. Use
a 3/8" x 3-1/4" hex bolt (A), a 3/8" washer (T), a 3/8"
lock washer (O), and a 3/8" hex lock nut (Z).

• Install a tensioning chain (JJ) through the hole shown

and then insert a 3/32" hairpin cotter (GG) into the 4th
link.

• Attach the chain to the spring on the lower idler arm.

CABLE
BRACKET (6)

5/16" x 3/4"
CARRIAGE BOLT (D)

5/16" NYLOCK
NUT (Y)

5/16" x 1"
HEX BOLT (C)

5/16" x 3/4"
HEX BOLT (D)

5/16"
NYLOCK
NUT (Y)

5/16" WASHER (Q)

(2) 5/16"
WASHERS (Q)

HEX BOLTS

(#48138)
DRIVE BELT

FLAT IDLER
PULLEYS

LARGE 3/8" SPACER (23)

3/8" LOCKWASHER (O)

3/8" HEX LOCK NUT (Z)

3/8" WASHER (T)

3/8" x 3-1/4"
HEX BOLT(A)

TENSIONING
CHAIN (JJ)

PULLEY (22)

(long end of
hub down)

3/32" HAIRPIN COTTER
IN 4TH LINK (GG)

STOP

Using the wrong holes will cause belt
misalignment!

«
...
7
8
9
10
11
...
»

Summary of Contents for LST42H





































Reviews:

No comments

Related manuals for LST42H

Brand: Parker Pages: 18

Brand: Simplicity Pages: 26

Brand: Murray Pages: 177

Brand: Yard force Pages: 11

Brand: Dustcontrol Pages: 82

Brand: Maruyama Pages: 16

Brand: Gast Pages: 12

Brand: Columbia Pages: 16

Brand: Columbia Pages: 14

Brand: Cub Cadet Pages: 28

GRIZZLY GP-1 ETL

Brand: B-Air Pages: 8

Brand: Fayat Group Pages: 74

GALB-E 40 Li OA

Brand: Gardol Pages: 236

Brand: Parker Pages: 20

Brand: ebm-papst Pages: 11

Garden Technic ASB40LI-2A

Brand: elem Pages: 45

Brand: Echo Pages: 58

PB-251E - PARTS CATALOG SN P09012001001 - P09012999999 REV...

Brand: Echo Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands