manualshive.com logo in svg

SpeedEPart LST42H, Manual, Page: 8 / 36

Share
Download
SpeedEPart LST42H Manual Download Page 8

8

STEP 4:  (SEE FIGURE 4)

•

 

Install a shoulder bolt (M), a 3/8" washer (T) and a 
3/8" flanged lock nut (X) in the R.H. (21) and L.H. (20)  
Side Plates.

FIGURE 4 

 

 

        RIGHT SIDE VIEW

FIGURE 3 

RIGHT SIDE VIEW

5/16"
NYLOCK
NUT

5/16" x 1"
CARRIAGE BOLT (K)

ENGINE MOUNTING 
PLATE

(4) 1/2" WASHERS (R)

(3) 3/8" FLANGE NUTS (X)

(3) 3/8" x 1"
CARRIAGE
BOLTS (H)

SEE NOTE

INSTALL SIDE PLATES

STEP 3:  (SEE FIGURE 3)

•  Fasten the R.H. Side Plate (bend facing out) to the 

front three holes in the tractor frame using three 3/8" 
x 1" carriage bolts (H), three 1/2" washers (R) (see 
note) and three 3/8" flange nuts (X).  For the rear hole, 
use a 5/16" x 1" carriage bolt (K), a 1/2" washer (R) 
and a 5/16" nylock nut (Y).  Place the 1/2" washers 
between the tractor frame and the side plate. Repeat 
for L.H. side plate.

•  Reinstall the browning shield onto the tractor frame 

using the original screws.

NOTE:

 If there is an engine mounting plate (shown with 

dotted lines) leave the 1/2 washer off the bolt that goes 
through the plate.

INSTALL HANGER BRACKETS AND SHOULDER 
BOLTS TO OUTSIDE OF FRAME

STEP 5:  (SEE FIGURE 5)

•

 

Remove the bolt, if present, in the hole directly behind 
the brake rod on the left side of the tractor frame.

•  Attach the L.H. Hanger Bracket (16) to the hole using 

a 5/16" x 3/4" self threading bolt (G).

•  Install a shoulder bolt (M) into the hole that is 9-1/2" to 

the rear of the bolt you just installed. Secure it with a 
3/8" flange nut (X) on the inside of the frame.

FIGURE 5 

LEFT SIDE VIEW

5/16" x 3/4" SELF
THREADING BOLT (G)

L.H. HANGER

BRACKET (16)

BRAKE ROD

3/8" FLANGED NUT (X)

SHOULDER
BOLT (M)

5/16" x 3/4" SELF
THREADING BOLT (G)

R.H. HANGER
BRACKET (17)

RIGHT END OF
BRAKE ROD

3/8" FLANGED
NUT (X)

SHOULDER

BOLT (M)

STEP 6:  (SEE FIGURE 6)

•

 

Remove the bracket, if present, from the hole directly 
behind the end of the brake rod on the right side of 
the tractor frame. Store the bracket and bolt.

•  Attach the R.H. Hanger Bracket (17) to the hole using 

a 5/16" x  3/4" self threading bolt (G).

•  Install a shoulder bolt (M) into the hole that is 9-1/2" to 

the rear of the bolt you just installed. Secure it with a 
3/8" flange nut (X) on the inside of the frame.

FIGURE 6 

RIGHT SIDE VIEW

3/8" WASHER (T)

SHOULDER 
BOLT (M)

3/8" FLANGED
NUT (X)

Summary of Contents for LST42H





































Reviews:

No comments