Spectrum Technologies FIELDSCOUT 6435 Product Manual Download Page 11

Page: 11 / 32

Moisture Type

: Selects displayed moisture mode VWC%, Peri-

od, or TDR 300.

VWC%: Volumetric Water Content with EC compensation.

Period: Raw sensor reading in microseconds (us).

TDR 300: VWC without EC compensation

EC Units

: EC value (mS/cm) or Salinity Index (see p. 25).

Auto

Off

: Power off delay: 15, 30, 45, 60 minutes.

Current Date, Current Time

: Displays or changes current val-

ues. See p. 13 for details.

Timezone

: Offset from Greenwich Mean Time. As the offset

changes, the Time and Date will update.

Daylight Savings

: ON or OFF.

Calibration

*: Overrides factory calibration. See Appendix

Clear User Calibration

: Clears the user applied calibration back

to factory settings

Factory Defaults

*: Resets menu settings and counter to the fac-

tory default value.

About

: General information (Model and serial number, firmware

versions for display and sensor).

* Pressing Select button for these options brings up an additional

screen.

Rod Length

None

Soil Type

Standard

Backlight, GNSS,

Bluetooth

Disabled

Sound

Temperature

Fahrenheit

Temp Source

Soil Sensor

Moisture

VWC

EC units

mS/cm

Auto

Off

15 minutes

Time Zone

GMT

Summary of Contents for FIELDSCOUT 6435

































Search results

Summary of Contents for FIELDSCOUT 6435

Reviews:

Related manuals for FIELDSCOUT 6435

Brands by name

Popular brands

Spectrum Technologies FIELDSCOUT 6435, Product Manual

Search results

Summary of Contents for FIELDSCOUT 6435

Reviews:

Related manuals for FIELDSCOUT 6435

Brands by name

Popular brands