background image

0118857R12 Page 18 of 20

Freedom XRS Elite Troubleshooting Guide

WARNING

Be sure the lectern movement does not interfere with objects or 

people.  Do not place any items under the lectern worksurface.

Symptom

Problem

Solution

Worksurface will 

not operate

Loss of power

Be sure control box is plugged into a live circuit.

Loose electrical connections

Make sure all electrical connections are securely plugged into the control box.

See wiring diagram on p.9 for reference.

Object encountered under 

the lectern worksurface

1.  Raise the worksurface by pressing the “up” button.

2.  Remove any items under the lectern worksurface.

3.  Reset the lift mechanism (see below for procedure.)

Misaligned actuators due to 

unbalanced loads

Reset Procedure

1.  Unplug, then re-plug the power cord into a wall outlet.
2.  Make sure all lift mechanism wire connections are in place and secure.
3.  Remove anything located under the worksurface.
4.  Press and hold the “Down” button to lower the worksurface to the lowest “work” 

position until it stops moving.

5.  Release the “Down” button.
6.  Press and hold the “Down” button for 30 seconds.  The worksurface will lower, 

bottom-out, slightly rises, then stop moving.  The worksurface must be completely 

lowered before resuming operation.

Note: If the worksurface does not lower when doing this step, release the 

“Down” button, and retry step 6.

7.  Release the “Down” button.  The lift mechanism has now been reset and the 

worksurface can be adjusted normally.

•  Lea este manual del propietario antes de la instalación u operación.

•  No permita que los niños muevan el atril.

•  Proceda lenta y cuidadosamente al mover el atril.

•  Solo para uso en interiores. No instale o guarde el atril donde quede 

expuesto a la humedad.

•  No obstruya las rendijas de ventilación.

•  Evite cargar el equipo de forma desigual dentro del atril. La distribución 

asimétrica del peso podría provocar que el atril se vuelque al momento 

de moverlo.

•  No permita que nadie se siente, pare o suba al atril.

• 

Para limpiar las superfi cies sucias, utilice un paño, trapo suave o 

esponja con jabón neutro o una solución de detergente. No utilice 

solventes o abrasivos ásperos.

•  El uso convencional de este atril es institucional. No contiene 

ninguna parte que pueda ser reparada por el usuario ni requiere 

de mantenimiento por parte de éste. Si fuera necesario darle 

mantenimiento, póngase en contacto con Spectrum Industries para 

obtener asistencia.

Prevención de accidentes eléctricos:

•  No enchufe el cable de alimentación a un cable de extensión.

•  Revise que los cables de alimentación no tengan ningún daño antes 

de cada uso. No utilice cables de alimentación que estén dañados.

•  Desenchufe el cable de alimentación del tomacorriente eléctrico 

sosteniendo el cable fi rmemente. No desenchufe el cable de 

alimentación jalando únicamente del cable.

•  No se pare, circule, jale o coloque ningún objeto sobre el cable de 

alimentación.

•  Para mayor seguridad, enchufe el atril a una conexión a tierra 

controlada por un interruptor de circuito GFI 

(interruptor de fallas de 

conexión a tierra)

.

•  Los dispositivos eléctricos no son juguetes. Los niños generalmente 

no están conscientes de los riesgos asociados con los dispositivos 

eléctricos. Este atril lo deberán utilizar siempre personas adultas o 

bajo su supervisión.

Advertencia

: reubicar equipo de audio y/o video a un mueble que no haya 

sido diseñado específi camente para tal uso, puede provocar la muerte o 

lesiones graves debido a que puede colapsarse o volcarse sobre un niño.

Advertencia

: existe peligro de muerte o lesiones graves si los niños 

se suben a un mueble de equipo de audio y/o video. Un control 

remoto o juguete colocado sobre el mueble puede alentar a un niño a 

subirse y provocar que el mueble se vuelque sobre el chico.

Instrucciones importantes de prevención de accidentes y cuidado

•  Lire ce guide d’utilisation avant l’assemblage ou l’utilisation.

•  Interdire aux enfants de déplacer le lutrin.

•  Déplacer le lutrin lentement et prudemment.

•  Utilisation à l’intérieur uniquement. Ne pas assembler et ne pas ranger 

le lutrin dans un endroit humide.

•  Ne pas boucher les prises d’air de ventilation.

•  Éviter le chargement mal réparti de l’équipement sur le lutrin. Un 

chargement mal réparti risque de faire basculer le lutrin en déplacement.

•  Interdire à quiconque de s’asseoir, de se tenir debout ou de grimper 

sur le lutrin.

•  Passer un chiffon doux ou une éponge, imbibés de solution nettoyante 

ou de savon liquide doux, sur les surfaces sales. Ne pas utiliser des 

solvants rudes ou des abrasifs.

•  Ce lutrin est destiné à un usage institutionnel. Il ne contient aucune 

pièce susceptible d’être réparée par l’utilisateur et ne nécessite aucun 

entretien de la part de celui-ci. Si une maintenance est requise, 

communiquer avec Spectrum Industries pour obtenir de l’aide.

Consignes de sécurité en électricité

•  Ne pas brancher le cordon d’alimentation sur une rallonge.

• 

Vérifi er que les cordons d’alimentation sont intacts avant chaque 

utilisation.  Ne pas les utiliser s’il sont abîmés.

•  Pour débrancher le cordon de la prise murale, saisir son bouton 

isolant et tirer; ne pas tirer le cordon.

•  Ne pas marcher, ne pas rouler et ne pas placer des objets sur le 

cordon d’alimentation; ne pas le traîner.

•  Pour plus de sécurité, brancher le lutrin sur une prise mise à la terre 

protégée par un 

disjoncteur de fuite de terre.

•  Les appareils électriques ne sont pas des jouets. Les enfants 

n’ont souvent pas conscience des dangers associés aux appareils 

électriques. Ce le lutrin doit donc être toujours utilisé par un adulte, ou 

sous la surveillance d’un adulte.

Avertissement 

- Reloger un équipement audio ou vidéo sur un meuble non 

conçu pour supporter cet équipement pourrait entraîner de graves blessures, 

voire la mort, à la suite de l’effondrement du meuble ou de sa chute sur un enfant.

Avertissement

 - Un enfant qui grimpe sur un meuble d’équipement 

audio ou vidéo pourrait subir des blessures graves ou mortelles. Une 

télécommande ou des jouets placés sur le meuble risquent d’inciter un 

enfant à y grimper : le meuble pourrait alors basculer et écraser l’enfant.

Consignes importantes de sécurité et d’entretien

Important Safety and Care Instructions

•  Read these instructions before assembly or operation.

•  Do not allow children to move the lectern.

•  Proceed slowly and carefully when moving the lectern.

•  For indoor use only.  Do not install or store the lectern where it will be 

exposed to moisture.

•  Do not block the ventilation openings.

•  Avoid uneven loading of the equipment into the lectern.  Uneven weight 

distribution could cause the lectern to tip when the lectern is moving.

•  Do not allow anyone to sit, stand, or climb on the lectern.

•  Use a damp, soft-cloth, or sponge, with mild soap or detergent solution 

to clean dirty surfaces.  Do not use harsh solvents or abrasives.

•  This lectern is intended for institutional use.  It does not have any user-

serviceable parts or user-maintenance requirements.  If servicing is 

necessary, please contact Spectrum Industries for assistance.

Electrical Safety:

•  Do not plug the power cord into an extension cord.

•  Inspect power cords for damage before each use.  Do not use power cords 

that are damaged.

•  Unplug power cord from electrical outlet by gripping the cord.  Do not unplug 

the power cord by pulling only on the cord.

•  Do not step on, drive over, drag, or place objects on the power cord.

•  For added safety, plug the lectern into a grounded outlet controlled by a GFI 

(Ground Fault Interrupter) circuit breaker.

•  Electrical devices are not toys.  Children are often unaware of the hazards 

associated with electrical devices.  This lectern must always be used by 

adults or with adult supervision.

Warning

 - Relocating audio and/or video equipment to furniture not specifi cally 

designed to support audio and/or video equipment may result in death or 

serious injury due to the furnishing collapsing or over turning onto a child.

Warning

 - Death or serious injury may occur when children climb 

on audio and/or video equipment furniture.  A remote control or 

toys placed on the furnishing may encourage a child to climb on the 

furnishing and as a result the furnishing may tip over on to the child.

Summary of Contents for Freedom XRS Elite Lectern





















Reviews: