manualshive.com logo in svg

Spectranetics CVX-300, Operator'S Manual

Share
Download
Spectranetics CVX-300 Operator'S Manual Download Page 44

44

7030-0068-26

28Jul16

Customer Service, Canada/US (719) 633-8333 / (800) 231-0978

Customer Service, 31 33 434 7050

CVX-300

® 

Excimer Laser System 

Version 26 

Operator’s Manual 

English / English

12. 

If the system has been in the Ready mode for five minutes without lasing, it returns to 
Standby mode.

Power Down

1. 

Press the Standby button.

2. 

Turn the keyswitch to the OFF (   ) position.

3. 

Disconnect the power cord from the power source.

4. 

Disconnect and store the Footswitch in the front storage compartment.

5. 

Close the catheter connector door.

6. 

Clean detector face with alcohol prep.

7. 

When not in use, the laser system should be protected from unqualified use by 
removing the key.

8. 

Cover the laser system.

Fault Codes

When a fault is detected by the system, a code number is displayed in the middle of the 
display window corresponding to the appropriate fault. Refer to the Troubleshooting 
Section of this manual. Always record the fault code number and report it to Spectranetics 
Customer Service.

Summary of Contents for CVX-300

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands