background image

SpectraLink Corporation 

Installation and Administration  

 

NetLink OAI Gateway 

5.

 

Configuration Procedures 

The OAI Gateway must be configured according to the type of system in use: 
NetLink Telephony Gateway system or IP system. If the NetLink OAI Gateway is 
being used in an IP phone system, the configuration proceeds independently of the 
IP system. If the system is using one or more NetLink Telephony Gateways, the 
OAI Gateway will communicate with them during configuration and operation. 
These configuration procedures should be done after the handsets have been 
configured in the NetLink Telephony Gateway.  
Generally, configuration follows these steps: 
1.

 

Establish type of system through 

OAI Box Configuration

 option, 

2.

 

Establish Network settings through

 Network Configuration

 option, 

3.

 

Configure the handsets through either 

OAI Line Configuration

 for NetLink 

Gateway systems or through 

Telephone Line Configuration

 option for IP systems. 

4.

 

(IP systems) Use the 

Feature Programming

 option to configure the function 

sequence that activates the OAI feature. (In NetLink Telephony Gateway 
systems, the OAI function sequence is programmed in the Telephony Gateway). 

PN: 72-0078-07-B.doc  

Page 17 

Summary of Contents for MOG600




































Reviews: