20
R
EFERENCE
& I
NSTALLATION
M
ANUAL
section [631] is the viewer for the device in section [601]
and section [638] is the viewer for the device in section [608]. Please
note that this feature only works with wireless transmitters assigned to an Expansion Input (zone) as described in
Wireless Transmitters to the Receiver
on page 19. A reading of 1 is the weakest and a reading of 8 is the strongest. An average
reading of 3 and up is acceptable. Sometimes moving the transmitter or control panel by a small amount will greatly increase the
signal reception.
After entering the desired section, ignore the first reading as it will not be accurate.
You can also use a beep sequence feature to verify a transmitter’s signal strength. When you press a transmitter’s tamper switch,
beep tones emanating from all the keypads connected to the communication bus will advise you of the transmitter’s signal strength.
This feature cannot be used with any remote controls assigned to the control panel.
6.3
SERIAL NUMBER DISPLAY
Section [630]
This feature will display the serial number of any wireless transmitter on any Spectra keypad.
6.4
SUPERVISION OPTIONS
The Supervision Options cannot be used with any remote controls assigned to the control panel.
6.4.1
C
HECK
-
IN
S
UPERVISION
Section [610]: Supervision Options
Option [1] OFF = Check-in supervision disabled (default)
Option [1] ON
= Check-in supervision enabled
Option
[1]
enables the Check-in Supervision feature. The Spectra 1759EX waits for each of its assigned wireless
transmitters to send a status signal within a specified time period (as programmed in
on page 21) to confirm their presence and functionality. If a device has not sent a signal within that time
period, the Spectra 1759EX can generate a trouble, an alarm, and/or transmit a report code to the monitoring station
(refer to
Wireless Transmitter Supervision Options
How Do I View a Wireless Transmitter’s Signal Strength?
1)
Press the
[
ENTER
]
key.
2)
Enter your
[
INSTALLER
CODE
]
.
3)
Enter the desired
[
SECTION
NUMBER
]
(from sections [631] to [638]).
4)
Press the transmitter’s tamper switch or open the corresponding zone.
5)
On an LED keypad:
The keypad will illuminate numbers 1 to 8.
On an LCD keypad:
The keypad will display numbers from 1 to 8 on the screen. For example, the LCD screen below
shows a signal strength reading of 5.
How Do I Attain a Wireless Transmitter’s Signal Strength using the Beep Sequence?
1)
Press the
[
ENTER
]
key.
2)
Enter your
[
INSTALLER
CODE
]
.
3)
Enter the desired
[
SECTION
NUMBER
]
(from sections [631] to [638]).
4)
Press the transmitter’s tamper switch or open the corresponding zone.
5)
Listen for the beep tones:
If the signal strength is less than 3 = One beep
If the signal strength is between 3 and 6 = Two beeps
If the signal strength is greater than 6 = Three beeps
How Do I View a Transmitter’s Serial Number?
1)
Press the
[
ENTER
]
key.
2)
Enter your
[
INSTALLER
CODE
]
.
3)
Enter the section
[630]
.
4)
Press the
[0]
key six times to clear the serial number.
5)
On an LED Keypad:
The serial number digits will appear one at a time by illuminating the corresponding LED light. To
view the next digit, press the
[
ENTER
]
key.
On an LCD Keypad:
The first three digits of the serial number will appear. Press the [
ENTER
] key three times to view the
next three digits.
Summary of Contents for 1759ex
Page 1: ...1759EX V1 0 REFERENCE INSTALLATION MANUAL 433MHZ 868MHZ 1759EX...
Page 2: ......
Page 55: ......