background image

7

General Description

Receiving Information

The Badu SwimJet Systems from Speck Pumps are designed to be installed during the construction of your pool to create a 
water treadmill for anyone wanting a therapeutic and effective exercise.

The Badu SwimJet Systems can be installed in any type of pool, large or small, from gunite to vinyl liner. It has no protruding 
parts ensuring pool user’s safety, is very compact and installs at minimal cost. The self-contained, flush-mounted unit is a 
jet-propulsion system that pumps water into the pool creating a current in excess of 5,700 gallons per minute from a single 
recessed jet housing.

Topping off the experience is the pulsating massage hose which can be attached to the jet nozzles for easy and convenient 
massage treatments for joints and muscles. (NOTE: The massage hose is sold separately.)

Badu

®

Stream II

Installation Information

1. Upon receipt of the swimjet system, check the cartons for damage. Open each carton and check the pump(s), jet housing(s), 
and control box for concealed damage, such as cracks, dents, or a bent base. If damage is found, contact the shipper or 
distributor where the swimjet was purchased. 

2. Inspect the contents of each carton and verify that all parts are included.  (See Image 1) 

A

D

F

B

E

C

G

Image 1
BaduStream II System (1 jet & 4 HP pump)

Flush-mount jet housing

Square, anti-entrapment cover (8

1

/

4

” x 8

1

/

4

”) 

undetectable pump suction. (Optional Round 
Cover available)

Adjustable water flow jet nozzle

Air regulator adjusts amount of air bubbles in 
water flow.

Control box complete with GFCI and WiFi 
control module.

SPECK Model 21-80/33GS 4.0 HP (or a SPECK 
Model 72-VI 3.5 HP) self-priming, single 
phase plastic pump with built-in thermal 
overload (no motor starter required). Optional 
three phase pump and control box available. 
(NOTE: Flooded suction pump available for 
installation below water level.)

System (ON/OFF) LED Touch Button - Complete with 1.5” threaded housing fits into any 1.5” return fitting. The 
Touch button turns the swimjet system ON/OFF. Waterproof button may be installed below water level.

A.

B.

C.

D.

E.

F.

G.

Summary of Contents for Badu Stream II





























Reviews: